Home » Motorola Manuals » Barcode Scanners » Motorola LS3408-FZ20005 » Manual Viewer

Motorola LS3408-FZ20005 User Manual - Page 84

Software Handshaking continued, ACK/NAK with ENQ, XON/XOFF

View all Motorola LS3408-FZ20005 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

6 - 14 Symbol LS3408 Product Reference Guide Software Handshaking (continued) ACK/NAK with ENQ This combines the two previous options. For re-transmissions of data, due to a NAK from the host, an additional ENQ is not required. ACK/NAK with ENQ XON/XOFF An XOFF character turns the scanner transmission off until the scanner receives an XON character. There are two situations for XON/XOFF: • The scanner receives an XOFF before it has data to send. When the scanner has data to send, it waits up to Host Serial Response Time-out for an XON character before transmission. If it does not receive the XON within this time, the scanner issues an error indication and discards the data. • The scanner receives an XOFF during a transmission. Data transmission then stops after sending the current byte. When the scanner receives an XON character, it sends the rest of the data message. The scanner waits up to 30 seconds for the XON. XON/XOFF

Section	Page
Symbol LS3408 Product Reference Guide	1
Warranty	4
Patents	4
Revision History	5
Table of Contents	6
About This Guide	15
Introduction	15
Chapter Descriptions	15
Service Information	17
Getting Started	19
Introduction	19
Unpacking the Scanner	20
Setting Up the Scanner	21
Installing the Interface Cable	21
Connecting Power (if required)	22
Connecting a Synapse Cable Interface	23
Removing the Interface Cable	23
Configuring the Scanner	23
Scanning	25
Introduction	25
Beeper Definitions	26
LED Definitions	27
Scanning in Hand-Held Mode	27
Aiming	28
Scanning in Presentation Mode	29
Decode Zone	30
Maintenance and Technical Specifications	33
Introduction	33
Maintenance	33
Troubleshooting	34
Technical Specifications	36
Scanner Signal Descriptions	38
User Preferences	41
Introduction	41
Scanning Sequence Examples	41
Errors While Scanning	42
User Preferences Default Parameters	42
User Preferences	43
Set Default Parameter	43
Parameter Scanning	44
Beeper Tone	44
Beeper Volume	45
Power Mode	45
Laser On Time	46
Beep After Good Decode	46
Trigger Mode	47
Aim Duration	48
Keyboard Wedge Interface	49
Introduction	49
Connecting a Keyboard Wedge Interface	50
Keyboard Wedge Default Parameters	51
Keyboard Wedge Host Types	52
Keyboard Wedge Host Types	52
Keyboard Wedge Country Types (Country Codes)	53
Ignore Unknown Characters	55
Keystroke Delay	55
Intra-Keystroke Delay	56
Alternate Numeric Keypad Emulation	56
Caps Lock On	56
Caps Lock Override	57
Convert Wedge Data	57
Function Key Mapping	58
FN1 Substitution	58
Send Make and Break	58
Keyboard Maps	59
ASCII Character Set	61
RS-232 Interface	71
Introduction	71
Connecting an RS-232 Interface	72
RS-232 Default Parameters	73
RS-232 Host Parameters	74
RS-232 Host Types	76
Baud Rate	77
Parity	78
Check Receive Errors	79
Stop Bit Select	80
Data Bits	80
Hardware Handshaking	81
Software Handshaking	83
Host Serial Response Time-out	85
RTS Line State	86
Beep on <BEL>	86
Intercharacter Delay	87
Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options	88
Ignore Unknown Characters	88
ASCII / Character Set	89
USB Interface	95
Introduction	95
Connecting a USB Interface	96
USB Default Parameters	97
USB Host Parameters	98
USB Device Type	98
USB Country Keyboard Types (Country Codes)	99
USB Keystroke Delay	101
USB CAPS Lock Override	102
USB Ignore Unknown Characters	102
Emulate Keypad	103
USB Keyboard FN 1 Substitution	103
Function Key Mapping	104
Simulated Caps Lock	104
Convert Case	105
ASCII Character Set	106
IBM 468X/469X Interface	117
Introduction	117
Connecting to an IBM 468X/469X Host	118
IBM Default Parameters	119
IBM 468X/469X Host Parameters	120
Port Address	120
Convert Unknown to Code 39	120
Wand Emulation Interface	123
Introduction	123
Connecting a Wand Emulation Interface	124
Wand Emulation Default Parameters	125
Wand Emulation Host Parameters	126
Wand Emulation Host Types	126
Leading Margin (Quiet Zone)	127
Polarity	127
Ignore Unknown Characters	128
Convert All Bar Codes to Code 39	129
Convert Code 39 to Full ASCII	130
Scanner Emulation Interface	131
Introduction	131
Connecting Using Scanner Emulation	132
Scanner Emulation Default Parameters	133
Scanner Emulation Host	134
Scanner Emulation Host Parameters	134
Beep Style	134
Parameter Pass-Through	135
Convert Newer Code Types	136
Module Width	136
Convert All Bar Codes to Code 39	137
Code 39 Full ASCII Conversion	137
Transmission Timeout	138
Ignore Unknown Characters	139
Leading Margin	140
Check For Decode LED	141
123Scan	143
Introduction	143
Communication with 123Scan	143
123Scan Parameter	144
Symbologies	145
Introduction	145
Scanning Sequence Examples	145
Errors While Scanning	145
Symbology Default Parameters	146
UPC/EAN	149
Enable/Disable UPC-A	149
Enable/Disable UPC-E	149
Enable/Disable UPC-E1	150
Enable/Disable EAN-13	150
Enable/Disable EAN-8	151
Enable/Disable Bookland EAN	151
Decode UPC/EAN/JAN Supplementals	152
User-Programmable Supplementals	155
UPC/EAN/JAN Supplemental Redundancy	155
Transmit UPC-A/UPC-E/UPC-E1 Check Digit	156
UPC-A Preamble	157
UPC-E Preamble	158
UPC-E1 Preamble	159
Convert UPC-E to UPC-A	160
Convert UPC-E1 to UPC-A	160
EAN-8/JAN-8 Extend	161
Bookland ISBN Format	161
Code 128	162
Enable/Disable Code 128	162
Enable/Disable GS1-128 (formerly UCC/EAN-128)	162
Enable/Disable ISBT 128	163
Code 39	164
Enable/Disable Code 39	164
Enable/Disable Trioptic Code 39	164
Convert Code 39 to Code 32	165
Code 32 Prefix	165
Set Lengths for Code 39	166
Code 39 Check Digit Verification	167
Transmit Code 39 Check Digit	167
Code 39 Full ASCII Conversion	168
Code 93	169
Enable/Disable Code 93	169
Set Lengths for Code 93	169
Code 11	171
Code 11	171
Set Lengths for Code 11	171
Code 11 Check Digit Verification	173
Transmit Code 11 Check Digits	174
Interleaved 2 of 5 (I 2 of 5)	175
Enable/Disable Interleaved 2 of 5	175
Set Lengths for Interleaved 2 of 5	175
I 2 of 5 Check Digit Verification	177
Transmit I 2 of 5 Check Digit	177
Convert I 2 of 5 to EAN-13	178
Discrete 2 of 5 (D 2 of 5)	179
Enable/Disable Discrete 2 of 5	179
Set Lengths for Discrete 2 of 5	179
Codabar (NW - 7)	181
Enable/Disable Codabar	181
Set Lengths for Codabar	181
CLSI Editing	183
NOTIS Editing	183
MSI	184
Enable/Disable MSI	184
Set Lengths for MSI	184
MSI Check Digits	186
Transmit MSI Check Digit(s)	186
MSI Check Digit Algorithm	187
GS1 DataBar (formerly Reduced Space Symbology)	188
GS1 DataBar	188
GS1 DataBar Limited	188
Convert GS1 DataBar to UPC/EAN	189
Redundancy Level	190
Redundancy Level 1	190
Redundancy Level 2	190
Redundancy Level 3	191
Redundancy Level 4	191
Security Level	192
Security Level 0	192
Security Level 1	192
Security Level 2	193
Security Level 3	193
Bi-directional Redundancy	193
Miscellaneous Scanner Options	195
Introduction	195
Scanning Sequence Examples	195
Errors While Scanning	195
Miscellaneous Default Parameters	196
Miscellaneous Scanner Parameters	197
Transmit Code ID Character	197
Scan Angle	198
Prefix/Suffix Values	198
Scan Data Transmission Format	199
FN1 Substitution Values	201
Transmit “No Read” Message	201
Synapse Interface	202
Advanced Data Formatting	203
Introduction	203
Rules: Criteria Linked to Actions	203
Using ADF Bar Codes	204
ADF Bar Code Menu Example	204
Rule 1: The Code 128 Scanning Rule	205
Rule 2: The UPC Scanning Rule	205
Alternate Rule Sets	205
Rules Hierarchy (in Bar Codes)	207
Default Rules	207
Special Commands	208
Pause Duration	208
Begin New Rule	208
Save Rule	208
Erase	209
Quit Entering Rules	209
Disable Rule Set	210
Criteria	211
Code Types	211
Code Lengths	215
Message Containing A Specific Data String	220
Actions	225
Send Data	225
Setup Field(s)	229
Modify Data	236
Pad Data with Spaces	237
Pad Data with Zeros	242
Beeps	247
Send Keystroke (Control Characters and Keyboard Characters)	248
Send Right Control Key	288
Send Graphic User Interface (GUI) Characters	289
Turn On/Off Rule Sets	295
Alphanumeric Keyboard	297
Standard Default Parameters	315
Programming Reference	321
Symbol Code Identifiers	321
AIM Code Identifiers	322
Sample Bar Codes	327
UPC-A	327
UPC-E	327
UPC-E1	327
EAN-13	328
EAN-8	328
Code 39	328
Trioptic Code 39	329
Code 93	329
Code 11	329
Codabar	330
MSI	330
Interleaved 2 of 5	330
Numeric Bar Codes	331
0, 1, 2	331
3, 4, 5, 6	332
7, 8, 9	333
Cancel	333
Index	342

Match case Limit results 1 per page

6 - 14

Symbol LS3408 Product Reference Guide

Software Handshaking (continued)

ACK/NAK with ENQ

This combines the two previous options. For re-transmissions of data, due to a NAK from the host, an additional

ENQ is not required.

ACK/NAK with ENQ

XON/XOFF

An XOFF character turns the scanner transmission off until the scanner receives an XON character. There are two

situations for XON/XOFF:

•

The scanner receives an XOFF before it has data to send. When the scanner has data to send, it waits up to

Host Serial Response Time-out for an XON character before transmission. If it does not receive the XON

within this time, the scanner issues an error indication and discards the data.

•

The scanner receives an XOFF during a transmission. Data transmission then stops after sending the current

byte. When the scanner receives an XON character, it sends the rest of the data message. The scanner

waits up to 30 seconds for the XON.

XON/XOFF