Netgear DM111PSP DM111PSP User Manual - Page 63

Table 5-4. WAN IP Settings, to continue. The WAN IP Settings screen displays. - dm111pspv2 bridge mode

Get Netgear DM111PSP - ADSL2+ Ethernet Modem PDF manuals and user guides View all Netgear DM111PSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

ADSL2+ Modem Router DM111PSPv2 User Manual 5. Click Next to continue. The WAN IP Settings screen displays. Figure 5-4 6. Enter or select the WAN IP settings that are explained in the following table. Your ISP will advise you which settings to use. Table 5-4. WAN IP Settings Setting Description IP address Select a radio button for the IP address setting: • Obtain an IP address automatically. The modem router acquires the IP address automatically. • Use the following IP address. Enter an IP address in the WAN IP Address field. Enable NAT Select this check box to enable NAT, which automatically assigns private IP addresses (10.1.1.x) to LAN-connected devices. PPP IP extension Select this check box to enable the modem router to function in semi bridge mode. This option is available only when the IP address is obtained automatically and when NAT is disabled. Add Default Route Select this check box to set the current PVC as the default route. If this check box is deselected, the first PVC that was enabled is set as the default route. MTU The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some ISPs you might need to reduce the MTU. This is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. Advanced WAN Configuration 5-5 v1.0, December 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
ADSL2+ Modem Router DM111PSPv2 User Manual
Advanced WAN Configuration
5-5
v1.0, December 2008
5.
Click
Next
to continue. The WAN IP Settings screen displays.
6.
Enter or select the WAN IP settings that are explained in the following table. Your ISP will
advise you which settings to use.
Figure 5-4
Table 5-4. WAN IP Settings
Setting
Description
IP address
Select a radio button for the IP address setting:
•
Obtain an IP address automatically
. The modem router acquires the IP
address automatically.
•
Use the following IP address
. Enter an IP address in the WAN IP Address
field.
Enable NAT
Select this check box to enable NAT, which automatically assigns private IP
addresses (10.1.1.x) to LAN-connected devices.
PPP IP extension
Select this check box to enable the modem router to function in semi bridge mode.
This option is available only when the IP address is obtained automatically and
when NAT is disabled.
Add Default Route
Select this check box to set the current PVC as the default route. If this check box
is deselected, the first PVC that was enabled is set as the default route.
MTU
The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is
1500 bytes, or 1492 bytes for PPPoE connections. For some ISPs you might need
to reduce the MTU. This is rarely required, and should not be done unless you are
sure it is necessary for your ISP connection.