Netgear GSM7248R GSM7224R / GSM7248R Hardware Installation Guide
Netgear GSM7248R Manual
View all Netgear GSM7248R manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7248R manual content summary:
- Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 1
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10351-01 November 2007 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 2
may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. It is hereby certified that the NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 3
and used in accordance with the instructions, may cause harmful interference to by turning the equipment off and on, the user is encouraged to try to correct the interference to certify that the NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R is shielded against the generation - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 4
to certify that the NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R is shielded against the a domestic environment, this product may cause radio interference, in which case the user may be required to take appropriate measures. Product and Publication Details Model Number: - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 5
i How to Use This Manual ii How to Print This Manual ii Chapter 1 Introduction GSM7224R Front Panel and LEDs 1-1 GSM7224R Rear Panel 1-2 GSM7248R Front Panel and LEDs 1-2 GSM7248R Rear Panel 1-3 Interpreting the LEDs ...1-3 Safety Instructions ...1-4 Chapter 2 Hardware Installation Package - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 6
Chapter 3 Troubleshooting Troubleshooting Chart 3-1 Additional Troubleshooting Suggestions 3-2 Appendix A Default Settings and Technical Specifications Default Settings ...A-1 Technical Specifications A-3 Appendix B Related Documents vi v1.0, November 2007 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 7
This Manual The NETGEAR® Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide describes how to install, configure, and troubleshoot the ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224R and the ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R. The - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 8
L2 Managed Switch with Static Routing GSM7224R ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R November 2007 For more information about network, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, "Related Documents". Note: Product updates - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 9
GSM7224R and GSM7248R Hardware Installation Guide • Printing manual opens in a browser window. • Click the print icon in the upper left of your browser window. Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 10
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide iv v1.0, November 2007 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 11
and basic troubleshooting for the ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224R and ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R. These switches can be free standing, or rack mounted in a wiring closet or an equipment room. For information about features for - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 12
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide GSM7224R Rear Panel The rear panel has a console port panel of the GSM7248R. The front panel contains LEDs, a USB port, a RST (reset) button, RJ-45 jacks, and copper/fiber combo ports. LEDs USB port Reset button Figure 1-3 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 13
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide GSM7248R Rear Panel The rear panel has a console port, a redundant power supply connector, and a standard AC power receptacle for the supplied power cord. Console Figure 1-4 Redundant - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 14
Switches GSM7224R and GSM7248R Hardware Installation Guide Table 1-1. LED or port 45-48 media for GSM7248R is changed to copper, the SFP LEDs change to Off status. Safety Instructions Use the follow service markings. - Do not service any product except as explained in your system documentation. - - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 15
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide - The product does not operate correctly when you follow the operating instructions. • Keep your system away from radiators and heat sources. Also, do not block cooling vents. • Do not spill food or liquids on your system - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 16
GSM7224R and GSM7248R Hardware Installation Guide • To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). • Position system cables and power cables carefully; route cables so - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 17
software - Documentation including the Managed Layer 2 Switches 7200R Series CLI Reference Manual Version 7.0, the NETGEAR 7000 Series Managed Switch Administration Guide Version 6.0, the NETGEAR Installation Guide 7000 Series Managed Switch (7200R, 7300S), and this guide • Warranty and Support card - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 18
GSM7248R Hardware Installation Guide Protecting Against Electrostatic Discharge Warning: Static electricity can harm delicate components inside your system. To prevent static damage, discharge static found missing or damaged, contact your local NETGEAR reseller for replacement. 5. Inspect the - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 19
Switches GSM7224R and GSM7248R Hardware Installation Guide Installation Install the The switch can be mounted in a standard 19-inch (48.26-centimeter) rack, wall mounted, or left freestanding (placed the switch are shown in Appendix A, "Default Settings and Technical Specifications." Be sure that - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 20
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table 2-1. Site Requirements for Switch Location adequate airflow in the room or wiring closet where you will install the switch. Route the cable to avoid sources of electrical noise such as radio transmitters, broadcast - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 21
Switches GSM7224R and GSM7248R Hardware Installation Guide 3. Tighten the Verify that all cables are installed correctly. 3. Check cable routing to ensure that cables are not damaged and will not troubleshooting, see Chapter 3, "Troubleshooting." Hardware Installation 2-5 v1.0, November 2007 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 22
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide SFP Modules The module bay accommodates a standard SFP module with an LC connector that is compatible with the IEEE 802.3z 1000BASE-X standard. SFP modules - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 23
GSM7248R Hardware Installation Guide NETGEAR product support website http://www.kbserver.com. Select your product in the Product Support section of the screen. When the product support can use the command line interface (CLI) to identify the IP address. If you are stacking switches, see "Connecting a - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 24
as both a print document and in PDF format on the Resource CD). • Managed Layer 2 Switches 7200R Series CLI Reference Manual Version 7.0. Gives detailed examples of how to use the CLI, and is located on the Resource CD. • NETGEAR 7000 Series Managed Switch Administration Guide Version 6.0. Describes - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 25
symptoms, causes, and solutions of possible problems. Table 3-1. Troubleshooting Chart Problem Power LED is off. Cause No power all products are functioning. File transfer is slow, or performance degradation is a problem. Half or full duplex setting on the switch and the connected device are not - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 26
and GSM7248R Hardware Installation Guide Table 3-1. Troubleshooting Chart (continued) Problem Cause resetting the switch. To reset the switch, use the Tools > Reset command, or remove AC power from the switch and then reapply AC power. If the problem continues, contact NETGEAR Technical Support - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 27
and ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R. Default Settings The following table lists the factory default settings for the switches. You can use the RST (reset) button to return a switch to its factory default settings. Table A-1. Default Configuration Settings Features - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 28
Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table A-1. Default Configuration Settings (continued) Features Admin edge port Link aggregation Port mirroring Traffic prioritization ACL GVRP GMRP IP routing MAC address aging SNMP community VLAN Ingress filtering GSM7224R - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 29
1Q Static VLAN (Up to 4k) • 802.1p Class of Service (CoS) • 802.1D Spanning Tree Protocol (STP) • 802.1w Rapid Spanning Tree Protocol (RSTP) • 802.1s Multiple Spanning Tree Protocol (MSTP) • 802.3ad Link Aggregation (LACP) • IGMP v1, v2 Snooping Support Default Settings and Technical Specifications - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 30
2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table A-2. Technical Specifications (continued) Feature GSM7224R GSM7248R Layer 3 services • Static routing • ACL • DiffServ QOS • DHCP, BOOTP Relay • DHCP server • UDP Relay • ARP • IGMP querier • Static routing • ACL • DiffServ QOS - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 31
Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table A-2. Technical Specifications (continued) Feature GSM7224R Environment Operating: • Temperature 22.2 #950) • UL listed (UL 1950)/cUL IEC950/ EN60950 Default Settings and Technical Specifications A-5 v1.0, November 2007 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 32
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide A-6 Default Settings and Technical Specifications v1.0, November 2007 - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 33
/reference/enu/winzerocfg/index.htm Configuration Utilities Internet Networking and TCP/IP http://documentation.netgear.com/reference/enu/tcpip/index.htm Addressing Wireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htm Preparing a Computer for Network Access - Netgear GSM7248R | GSM7224R / GSM7248R Hardware Installation Guide - Page 34
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide B-2 Related Documents v1.0, November 2007
202-10351-01
November 2007
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Managed Layer 2
Switches GSM7224R
and GSM7248R
Hardware Installation
Guide