Olympus C-60 Zoom C-60 Zoom Reference Manual - Page 147

Possible cause, Corrective action, Ref. The viewfinder display is not clear.

Page 147 highlights

Troubleshooting Possible cause Corrective action Ref. Page No picture is taken when the shutter button is pressed. There is a problem with the Refer to "Error codes". card. P. 143 The viewfinder display is not clear. There is condensation* in Wait until the camera dries - the viewfinder. before turning it on again. The monitor is hard to see. The brightness is not adjusted properly. Select in the MODE MENU and adjust the brightness. P. 117 The monitor is exposed to Block the sunlight with your - direct sunlight. hand. Vertical lines appear on the Aiming the camera at a bright - monitor screen during subject in sunlight may cause shooting. vertical lines to appear on the screen. This is not a malfunction. The date recorded with the image data is wrong. The date/time is not set. Set the date/time. The clock adjustment is not factory-preset. P. 24 The camera has been left If the camera is left for about 1 P. 24 with the battery removed. day with the battery removed, the date/time setting is canceled. Set the date/time again. The settings are returned to the factory default settings when the camera is turned off. ALL RESET is set to ON. Set ALL RESET to OFF in the P. 103 10 MODE MENU. * Condensation: When it is cold outside, the water vapor in the air is rapidly cooled and turns to droplets of water. Condensation occurs when the camera is suddenly taken from a cold place into a warm room. Miscellaneous 146

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205

No picture is taken when the shutter button is pressed.
146
Troubleshooting
10
Miscellaneous
The date recorded with the image data is wrong.
Possible cause
Corrective action
Ref. Page
*
Condensation: When it is cold outside, the water vapor in the air is rapidly cooled and
turns to droplets of water.
Condensation occurs when the camera is suddenly taken from a cold
place into a warm room.
The monitor is hard to see.
The settings are returned to the factory default settings when the
camera is turned off.
The viewfinder display is not clear.
There is a problem with the
card.
There is condensation* in
the viewfinder.
The brightness is not
adjusted properly.
The monitor is exposed to
direct sunlight.
Vertical lines appear on the
monitor screen during
shooting.
The date/time is not set.
The camera has been left
with the battery removed.
ALL RESET is set to ON.
P. 143
P. 117
P. 24
P. 24
P. 103
Refer to “Error codes”.
Wait until the camera dries
before turning it on again.
Select
in the MODE MENU
and adjust the brightness.
Block the sunlight with your
hand.
Aiming the camera at a bright
subject in sunlight may cause
vertical lines to appear on the
screen. This is not a
malfunction.
Set the date/time. The clock
adjustment is not factory-preset.
If the camera is left for about 1
day with the battery removed,
the date/time setting is canceled.
Set the date/time again.
Set ALL RESET to OFF in the
MODE MENU.