Onkyo HT-S7200 Owner Manual - Page 112

Attaching the Speaker Bases, SAFETY PRECAUTIONS

Get Onkyo HT-S7200 PDF manuals and user guides View all Onkyo HT-S7200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

Getting to know Your Speaker Package-Continued Attaching the Speaker Bases Before you connect the speakers, attach the supplied speaker base to each SKF-770. 1. Turn the speaker upside down with the protection cover attached. 2. Align the speaker base while the arrow mark is headed in the same direction as the speaker's face. Be careful not to tip over the speaker. 3. Align the screw holes on the speaker base with those on the bottom of each speaker, and affix the speaker base using the supplied screws. Recommended torque is 10 kgf·cm (9 lbf·in). Be careful not to tip over the speaker. 4. Turn the speaker right side up. 5. Remove the protection cover. SAFETY PRECAUTIONS: • Attach the speaker bases in a manner that will not allow the speakers to tip over. • Be sure to tighten the screws when you attach the speaker bases. • Attach the speaker bases on a flat, level, and stable floor. • After you attach the speaker bases, make sure that the speakers stand upright and are stable. Top of SKF-770 Protection cover Supplied screws Arrow mark Speaker base Bottom of SKF-770 En-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
En-
8
Getting to know Your Speaker Package
—Continued
Before you connect the speakers, attach the supplied
speaker base to each SKF-770.
1.
Turn the speaker upside down with the protection
cover attached.
2.
Align the speaker base while the arrow mark
is
headed in the same direction as the speaker’s face.
Be careful not to tip over the speaker.
3.
Align the screw holes on the speaker base with
those on the bottom of each speaker, and affix the
speaker base using the supplied screws.
Recommended torque is 10 kgf·cm (9 lbf·in).
Be careful not to tip over the speaker.
4.
Turn the speaker right side up.
5.
Remove the protection cover.
SAFETY PRECAUTIONS:
•
Attach the speaker bases in a manner that will not
allow the speakers to tip over.
•
Be sure to tighten the screws when you attach the
speaker bases.
•
Attach the speaker bases on a flat, level, and stable
floor.
•
After you attach the speaker bases, make sure that the
speakers stand upright and are stable.
Attaching the Speaker Bases
Top of SKF-770
Protection cover
Supplied screws
Speaker base
Bottom of SKF-770
Arrow mark