Onkyo HT-S7200 Owner Manual - Page 51

Adjusting the Bass & Treble, Displaying Source Information, Setting the Display Brightness

Get Onkyo HT-S7200 PDF manuals and user guides View all Onkyo HT-S7200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Basic Operations-Continued -, +, TONE Press [RECEIVER] first DISPLAY Displaying Source Information You can display various information about the current input source as follows. Remote controller Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. DIMMER Adjusting the Bass & Treble You can adjust the bass and treble for the front speakers, except when the Direct listening mode is selected. 1 AV receiver Press the [TONE] button repeatedly to select either "Bass" or "Treble". 2 Use the TONE [-]/[+] buttons to adjust. ■ Bass You can boost or cut low-frequency sounds output by the front speakers from -10 dB to +10 dB in 2 dB steps. ■ Treble You can boost or cut high-frequency sounds output by the front speakers from -10 dB to +10 dB in 2 dB steps. Note: This procedure can also be performed on the remote controller by using [AUDIO] button (see page 72). Note: This procedure can also be performed on the AV receiver by using its [DISPLAY] button. The following information can typically be displayed for input sources. Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Setting the Display Brightness You can adjust the brightness of the AV receiver's display. Remote controller Press the [RECEIVER] button, and then press the [DIMMER] button repeatedly to select: dim, dimmer, or normal brightness. Alternatively, you can use the AV receiver's [DIMMER] button. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
51
Basic Operations
—Continued
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
■
Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■
Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
Note:
This procedure can also be performed on the remote con-
troller by using [AUDIO] button (see page 72).
You can display various information about the current
input source as follows.
Note:
This procedure can also be performed on the AV receiver
by using its [DISPLAY] button.
The following information can typically be displayed for
input sources.
*1
When AM or FM radio is used, the band, preset number, and
frequency are displayed.
*2
If the input signal is analog, no format information is displayed.
If the input signal is PCM, the sampling frequency is displayed.
If the input signal is digital but not PCM, the signal format is
displayed.
Information is displayed for about three seconds, then the previ-
ously displayed information reappears.
You can adjust the brightness of the AV receiver’s dis-
play.
Adjusting the Bass & Treble
1
AV receiver
Press the [TONE] button repeat-
edly to select either “Bass” or
“Treble”.
2
Use the TONE [–]/[+] buttons to
adjust.
DISPLAY
DIMMER
–, +, TONE
Press
[RECEIVER]
first
Displaying Source Information
Remote
controller
Press the [RECEIVER] button,
and then press the [DISPLAY]
button repeatedly to cycle
through the available informa-
tion.
Setting the Display Brightness
Remote
controller
Press the [RECEIVER] button,
and then press the [DIMMER]
button repeatedly to select: dim,
dimmer, or normal brightness.
Alternatively, you can use the AV
receiver’s [DIMMER] button.
Input source &
volume
*1
Signal format
*2
or sampling
frequency
Input source &
listening mode