Onkyo TX-NR747 User Manual - Page 18

Step 3, Multi-zone

Get Onkyo TX-NR747 PDF manuals and user guides View all Onkyo TX-NR747 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

6 Multi-zone You can listen to audio in a room (called Zone 2) other than the one where this unit is located (called the main room).  Sources you can playback ●● External players (1) ●● NET (2) ●● Bluetooth ●● AM/FM Radio 1 Only analog and 2ch PCM audio signals can be output to Zone 2. 2 DSD and Dolby TrueHD audio signals cannot be output to Zone 2. Important: Connection with external players To listen to a player in Zone 2, you must connect using an RCA cable, a digital optical cable (OPTICAL), or a digital coaxial cable (COAXIAL). Some players may require audio output setting. Making Multi-zone Connection There are the following two methods of connection: a. Connecting with a pre-main amplifier in a separate room b. Connecting with speakers in a separate room  a. Connecting with a pre-main amplifier in a separate room It is possible to play 2 ch source in a separate room while 7.1 ch source is being played in the main room. Connect the LINE OUT ZONE2 jacks of the unit and the line-in jacks of the pre-main amplifier in a separate room with an RCA cable. Step 3: Playing Back  b. Connecting with speakers in a separate room Connect the speakers in another room to the SPEAKERS ZONE2 jacks of the unit using speaker cables. Note that 5.1 ch will be the maximum () in the main room during Zone 2 playback. No sound will be output from the back speakers and height speakers. ¼¼In this case, the Dolby Atmos listening mode cannot be selected. DIGITAL OPTICAL OUT AUDIO OUT Main room Main room Zone 2 ●● The volume should be adjusted with the pre-main amplifier used in the separate room. Zone 2 These settings are required: After connecting the speakers, press RECEIVER and then SETUP on the remote controller, select "2. Speaker" "Configuration" and set "Powered Zone2" to "Yes". ●● Adjust the volume on this unit. To adjust the volume, press ZONE2 on the remote controller and then adjust with VOLj/l. To control on the main unit, press ZONE 2 and within 8 seconds, adjust with the MASTER VOLUME control. You can mute the sound by pressing MUTING on the remote controller. En-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Step 3:
Playing Back
En-18
6
Multi-zone
You can listen to audio in a room (called Zone 2) other than
the one where this unit is located (called the main room).
Sources you can playback
●
External players (
1)
●
NET (
2)
●
Bluetooth
●
AM/FM Radio
1 Only analog and 2ch PCM audio signals can be output to Zone 2.
2 DSD and Dolby TrueHD audio signals cannot be output to Zone 2.
Important
: Connection with external players
To listen to a player in Zone 2, you must connect using an
RCA cable, a digital optical cable (OPTICAL), or a digital
coaxial cable (COAXIAL). Some players may require audio
output setting.
AUDIO
OUT
DIGITAL
OPTICAL
OUT
Making Multi-zone Connection
There are the following two methods of connection:
a. Connecting with a pre-main amplifier in a separate room
b. Connecting with speakers in a separate room
a� Connecting with a pre-main amplifier in a
separate room
It is possible to play 2 ch source in a separate room while
7.1 ch source is being played in the main room.
Connect the LINE OUT ZONE2 jacks of the unit and the
line-in jacks of the pre-main amplifier in a separate room
with an RCA cable.
Main room
Zone 2
●
The volume should be adjusted with the pre-main
amplifier used in the separate room.
b� Connecting with speakers in a separate
room
Connect the speakers in another room to the SPEAKERS
ZONE2 jacks of the unit using speaker cables. Note that
5.1 ch will be the maximum (
) in the main room during
Zone 2 playback. No sound will be output from the back
speakers and height speakers.
In this case, the Dolby Atmos listening mode cannot be selected.
Main room
Zone 2
These settings are required
: After connecting the
speakers, press
RECEIVER and then SETUP
on the remote controller, select "2. Speaker" -
"Configuration" and set "Powered Zone2" to "Yes".
●
Adjust the volume on this unit. To adjust the
volume, press ZONE2 on the remote controller
and then adjust with VOL
j
/
l
. To control on the
main unit, press ZONE 2 and within 8 seconds,
adjust with the MASTER VOLUME control. You
can mute the sound by pressing MUTING on the
remote controller.