Optoma EH319UST User manual

Optoma EH319UST Manual

Get Optoma EH319UST PDF manuals and user guides View all Optoma EH319UST manuals
Add to My Manuals
Save this manual to your list of manuals

Optoma EH319UST manual content summary:

  • Optoma EH319UST | User manual - Page 1
    TouchBeam Interactive TouchBeam interactive User manual
  • Optoma EH319UST | User manual - Page 2
    Guide...11 Installation workflow...11 Installing the mount...12 Step 1: Attach the wall plate to the wall...12 Step 2: Attach the projector to the mount plate 13 Step 3: Attach the projector Sensitivity...31 Step 9: Troubleshooting Viewer...32 Appendix...33 Troubleshooting...33 Interactive cable
  • Optoma EH319UST | User manual - Page 3
    follow all warnings, precautions and maintenance as recommended in this user's manual.  Warning - Do not disassemble the TouchBeam module.  to enter the TouchBeam module. Precautions The IR camera on the projector receives infrared signals from the TouchBeam module which is attached to the
  • Optoma EH319UST | User manual - Page 4
    Package Overview TouchBeam module 2x (M2 6mm) screws 2x (M6 6mm) screws Interactive cable power cable 2x Alignment sticker sticjestickers TouchBeam bracket mounting plate Double sided tape TouchBeam mounting plate 5m USB cable 2x Passive pens CD user manual software 4
  • Optoma EH319UST | User manual - Page 5
    TouchBeam module ensure that the power supply and wiring work for the installation location of the mount in advance. Note:  Install the projector away from other electrical devices such as florescent lights or air conditioners. Some kinds of florescent lights could interfere with the remote control
  • Optoma EH319UST | User manual - Page 6
    with screws If the projection surface meets the criteria above, the projector and TouchBeam module can then be installed in one of the following ways 1. Mount the projector and TouchBeam module to the wall 2. Mount the projector to the wall and attached the TouchBeam module to the whiteboard
  • Optoma EH319UST | User manual - Page 7
    Whiteboard guideline When installing the TouchBeam module on a whiteboard please follow the guidelines below For standard aspect ratio (4:3, 16:10 and 16:9) image sizes  Image size: 70" ~ 115"*  From the top of image area, a 20~100mm gap must be kept away from the bottom of TouchBeam module  For
  • Optoma EH319UST | User manual - Page 8
    For ultra-wide (24:9) image size  Image size: 120" ~ 140" Ultra wide  From the top of image area, a 40~100mm gap must be kept away from the bottom of TouchBeam module  For a suggested whiteboard with a frame height of
  • Optoma EH319UST | User manual - Page 9
    Note: If the whiteboard frame thickness is greater than 3mm the reflected light interference from the whiteboard frame may be detected by IR camera. This can compromise the touch function. To reduce the risk of this happening it is recommend that a 50mm border is kept around the projected image
  • Optoma EH319UST | User manual - Page 10
    10
  • Optoma EH319UST | User manual - Page 11
    Measuring projection surface flatness  Criteria: overall surface flatness should have variance of less than 5mm.  Equipment: leveling instrument (1.2~1.5m) and thickness gauge. Split projection area into 16 segments equally as shown on chart below. Place leveling instrument on whiteboard. Insert
  • Optoma EH319UST | User manual - Page 12
    workflow o Install the projector mount (See mount installation guide) o Attach the projector to mount (See mount installation guide) o Connect sources to the projector o Adjust projected images (See mount installation guide) o Install the whiteboard (See whiteboard installation guide) o Install the
  • Optoma EH319UST | User manual - Page 13
    Installing the mount Step 1: Attach the wall plate to the wall  For ease of installation mount the bracket on the wall using position 1 and mark other positions using a spirit level.  Remove bracket and drill other positions  Use fixings suitable for your type of wall construction  Use all
  • Optoma EH319UST | User manual - Page 14
    Step 2: Attach the projector to the mount plate  Place the projector on a soft clean surface  Position the pre-assembled mounting plate on top of the projector  Insert 5xA (M4 x 10mm) screws from the fixing kit, tighten with a posidrive screwdriver 14
  • Optoma EH319UST | User manual - Page 15
    and mounting plate in to position - Fig 3A  Lift the projector so the two hooks slip over the protrusions on the black molding - Fig 3B  Position the washer C and teardrop shaped locking washer D against the hooks -
  • Optoma EH319UST | User manual - Page 16
    the throw distance - Fig 4E  To reduce the projected image size, tighten the bolt clockwise using one of the allen keys provided to move the projector closer to the screen  To increase the projected image size, loosen the bolt anticlockwise using one of the allen keys provided to move the
  • Optoma EH319UST | User manual - Page 17
    Step 5: Adjusting the tilt (vertical keystone)  Loosen the single M8 x 75mm bolt - Fig 5A  Adjust the projector to the required angle - Fig 5B  Tighten the bolt to lock the angle of the projector - Fig 5C  Adjust the highlighted thumbwheel to fine adjust the tilt angle - Fig 5D  To decrease the
  • Optoma EH319UST | User manual - Page 18
    Step 6: Adjusting the tilt (yaw)  Adjust the highlighted thumbwheel to fine adjust the yaw angle - Fig 6E  To lower the left hand side of the projector, tighten the thumbwheel clockwise  To lower the right hand side of the projector, loosen the thumbwheel anticlockwise 18
  • Optoma EH319UST | User manual - Page 19
     Adjust the highlighted thumbwheel to fine adjust the rotation of the projector - Fig 7A  To bring the left hand side of the projector closer to the screen, tighten the thumbwheel clockwise  To bring the right hand side of the projector close to the screen, loosen the thumbwheel anticlockwise 19
  • Optoma EH319UST | User manual - Page 20
    Installing the whiteboard  Please refer to the whiteboard installation instructions Note: The whiteboard and projector should be installed centrally to each other. The bottom of the image must be a minimum of 10mm from the bottom of the whiteboard border. Enough
  • Optoma EH319UST | User manual - Page 21
    Installing the TouchBeam module Step 1: Mounting the TouchBeam module 1. Open top cover with a screwdriver. 1.2 Mount bracket to whiteboard or wall The module must be installed away from the projected image - At least 13.5cm from the base plate - At least 10cm from the bottom of the TouchBeam module
  • Optoma EH319UST | User manual - Page 22
    1.3b For long-term use: Use screws to fix the TouchBeam bracket onto the whiteboard: - Drill tip: Φ O=2.3mm - Screw type: M3x6L - Screw head: Φ O
  • Optoma EH319UST | User manual - Page 23
    Step 2: Install Utility Software 1. System requirements To ensure normal operation of the touch function, your computer must meet the system requirements shown in the table below. Operating system CPU Memory Min. hard disk space System requirement Microsoft Windows XP (SP3)/Windows 7 (32bit/
  • Optoma EH319UST | User manual - Page 24
    Step 3: Initial Setup For first time setup, follow the installation guide to complete the installation procedure ( ). 24
  • Optoma EH319UST | User manual - Page 25
    Operation Mode Windows 7 and Windows 8 operating systems support multi-point touch control. Users can select default Touch Mode ( ) for multi-point touch, Or switch to Pen Mode ( ) when using the light pen (IR pen). Please note: Windows XP and MAC operating systems only support single-point touch 25
  • Optoma EH319UST | User manual - Page 26
    indicator Red LED Description -- IR laser ON Blinking Visible light ON (IR Laser OFF, touch disabled) Solid Error of LD module occurred. 2. Connect PC and Projector via USB cable 3. Rotate the black and grey adjustment knobs clockwise until they stop 26
  • Optoma EH319UST | User manual - Page 27
    4. Rotate the grey knob counter-clockwise, until both beams are symmetrically at the same level. 5. Rotate black knob counter-clockwise, move beams downwards until they hit whiteboard frame. 6. Check the beam height with alignment the sticker for both left and right beams. The beams should be
  • Optoma EH319UST | User manual - Page 28
    7. Press the button again to switch back to IR mode (The Blue LED will stay solid) Mode IR Laser mode Visible light mode Error Blue LED Solid Solid -- LED indicator Red LED Description -- IR laser ON Blinking Visible light ON (IR Laser OFF, touch disabled) Always ON Error of LD module
  • Optoma EH319UST | User manual - Page 29
    during Touch Area Setting  Check if projection image is clear. If not, adjust focus to sharpen the image If fail message pops up, switch to Manual Touch Area Setting. B. Select Manual Touch Area Setting: 29
  • Optoma EH319UST | User manual - Page 30
    B-1. After the camera captures the projection image, a Touch Area window will pop up. If the captured image is not clear enough, please re-select "Ambient light mode selection" from "Auto" to "Bright" or "Dim" according to actual ambient light condition. Remark: Captured image shows the actual
  • Optoma EH319UST | User manual - Page 31
    Calibration Note: If the fail message pops up, follow the steps shown below to troubleshoot the issues.  Close all software applications  Reduce ambient light  Do not screen, switch to Manual Calibration. B. Select Manual Calibration: Note: Manual Calibration is suggested for better accuracy. 31
  • Optoma EH319UST | User manual - Page 32
    Step 8: Touch Sensitivity When touch function is unresponsive or writing is intermittent. You can adjust the sensitivity by adjusting Touch Sensitivity level: - Default: 4 - Max.: 10 (most sensitive) - Min.: 0 (least sensitive) 32
  • Optoma EH319UST | User manual - Page 33
    with touch performance. The troubleshooting viewer shows real time images for debugging purposes. Any light interference is marked in green. If green obstacles appear within image area, remove to secure proper interactivity. Note: Interactive function is disabled under trouble-shooting viewer, click
  • Optoma EH319UST | User manual - Page 34
    Appendix Troubleshooting Q1 Why won't the PC boot when the USB cable is connected to the projector? A: 1. Unplug USB cable from PC the USB driver to the latest version. 6. Use the USB cable included with your projector and check again. If a USB extension is needed please contact your distributor. 7.
  • Optoma EH319UST | User manual - Page 35
    . 6. Go to official website of the laptop/PC manufacturer, and update the BIOS driver to the latest version. 7. Use the USB cable included with your projector and check again. If an USB extension is needed, please contact your distributor. 8. The USB port of your computer may not be working. Please
  • Optoma EH319UST | User manual - Page 36
    calibration. - If an overlarge offset is observed, please perform Manual Calibration and see Step 8 Calibration for troubleshooting. Q6 What to do when Auto Calibration and Auto Touch Area Setting both fail? A: 1. When the projectors OSD message is shown, this may result in Auto Calibration failure
  • Optoma EH319UST | User manual - Page 37
    please switch to Manual Mode to complete Touch Area Setting and Calibration. 3. Please check Projector Brightness Mode selection. Lower lamp brightness (ECO to enhance sensitivity, see Step 9 Touch Sensitivity for troubleshooting. 2. If Touch function remains insensitive, please check the optical
  • Optoma EH319UST | User manual - Page 38
    particles are observed, gently clean the optical port with dust blower. Q10 What to do when the touch function is not accurate? A: Touch accuracy may be impacted when the Windows default display has been changed. 1. Go to the setting page 2.
  • Optoma EH319UST | User manual - Page 39
    Appendix Interactive cable layout 39
  • Optoma EH319UST | User manual - Page 40
    Distance calculator XGA B 0.219m 0.252m 0.287m 0.354m 0.422m A 0.472m 0.505m 0.540m 0.607m 0.675m W 1.422m 1.521m 1.627m 1.828m 2.033m H 1.066m 1.141m 1.220m 1.371m 1.525m Image size 1.777m / 70" 1.879m / 75" 2.033m / 80" 2.285m / 90" 2.541m / 100" D 0.181m 0.194m 0.207m 0.233m 0.259m M 0.37m
  • Optoma EH319UST | User manual - Page 41
    1080p B 0.193m 0.244m 0.249m 0.305m A 0.446m 0.497m 0.502m 0.558m W 1.770m 1.972m 1.992m 2.214m H 0.996m 1.109m 1.121m 1.246m 2.031m / 80" 2.263m / 89" 2.286m / 90" 2.541m / 100" D 0.179m 0.200m 0.202m 0.224m M 0.37m 0.39m 0.39m 0.42m N 1.49m 1.63m 1.64m 1.79m Ultra wide* B A W 0.467m 0.
  • Optoma EH319UST | User manual - Page 42
    -20℃~+60℃ II. General Specifications Calibration Auto Calibration Manual Calibration Multi-touch 10-touch points (Win 7 and UST projector) Display mode Support Ceiling mode only IR camera hot plug IR camera cannot support hot plug. Please unplug AC power cord of projector before install
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
TouchBeam Interactive
User manual