Panasonic DMP-BD10 Blu-ray Dvd Player - English/ French - Page 23

Settings Changing the unit's settings Tabs HDMI Menus Options (Underlined items are the factory presets.) HDMI Video Mode Select "On" when video is output from HDMI AV OUT terminal. pOn: [Note]:Video from COMPONENT VIDEO OUT terminal is output as "480i" if this is selected. pOff HDMI Resolution You can only select settings compatible with the connected equipment. This setting normally does not need to be changed. However if you are concerned about output picture quality, it may be improved by changing the setting. Still pictures play at a resolution equivalent to 480p regardless of the settings. pAuto: p480p p720p p1080i p1080p Automatically selects the output resolution best suited to the connected television (1080p, 1080i, 720p or 480p). HDMI RGB Output Range pStandard: Effective when connected to a device that only supports RGB pEnhanced: When the black and white images are not output. distinct. HDMI Audio Output This setting selects whether or not to output audio from HDMI. [Note]:If "On" is selected, audio output from the 7.1ch AUDIO OUT terminal will match the number of channels on the equipment connected with HDMI. pOn: pOff: When the TV is connected to this unit with an HDMI cable, and you are connected to an amplifier/receiver that does not support HDMI. Ctrl with HDMI pOn: When "On" is selected, you can operate other EZ Sync HDAVI control compatible devices (➡ 18). pOff: Changing the speaker setting to suit your speakers When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on the amplifier/receiver. 5.1ch speaker connection 7.1ch speaker connection Front (L) Center Front (R) Approximate room dimensions C C L C R L C R Complete L ms 0.0 C dB 0.0 R dB dB 0.0 0.0 Complete Test dB 0.0 SW Subwoofer LS LS SW RS RS LS LS LB LB SW RS RS RB RB Test dB ms dB LS 0.0 0.0 0.0 RS dB ms dB 0.0 LB 0.0 RB 0.0 (LS) Surround (RS) (LB) Surround back (RB) Speaker presence and size () Press to select the speaker icon () and press [ENTER]. Press [, ] to select the setting and press [ENTER]. Icon examples: Surround speaker (LS) pLarge: Select when the LS LS speaker supports Large Small No low-frequency (under 100 Hz) reproduction. pSmall: Select when the speaker does not support low-frequency reproduction. In order to make an ideal listening environment, settings of speaker sizes may be automatically adjusted. For example, if the subwoofer is set to "No", the front speakers will automatically be set to "Large". (In this case, we recommend connecting a speaker that can reproduce bass below 100 Hz.) Delay time () (Effective when playing multi-channel audio) (Center, surround and surround back speakers only) For optimum listening with 7.1/5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating position. If you have to place the center, surround and surround back speakers closer to the seating position, adjust the delay time to make up for the difference. If either distance or is less than , find the difference in the relevant table and change to the recommended setting. Press to select the delay time box () and press [ENTER]. Press [, ] to select the setting and press [ENTER]. Circle of constant primary listening distance : Actual speaker position : Ideal speaker position : Primary listening distance Settings  Center speaker Difference Approx. 34 cm (11e10 feet) Approx. 68 cm (21e5 feet) Approx. 102 cm (33e10 feet) Approx. 136 cm (42e5 feet) Approx. 170 cm (51e2 feet) Setting 1.0 ms 2.0 ms 3.0 ms 4.0 ms 5.0 ms Surround/Surround back speakers Difference Setting Approx. 170 cm (51e2 feet) 5.0 ms Approx. 340 cm (11 feet) 10.0 ms Approx. 510 cm (161e2 feet) 15.0 ms Channel balance () (Effective when playing multi-channel audio) This does not work when connected with HDMI terminals and "HDMI Audio Output" (➜ above, "HDMI" tab) is set to "On". Select "Test" and press [ENTER]. A test signal is output. Front (L)(Center(Front (R)(Surround (RS)   Surround (LS)(Surround Back(LB) (Surround Back (RB) While listening to the test signal, press [ ] to adjust the volume of each speaker Front speakers: 0.0 to U6.0 dB Except for front speakers: 0.0 to U12.0 dB Press [ENTER]. The test signal stops. pNo signal is output for the subwoofer. To adjust its volume, play something, then return to this screen to adjust to suit your taste. To finish the speaker setting Press [   ] to select "Complete" and press [ENTER]. RQT8745 23