Panasonic PT-LB90NTEA User Manual - Page 33

Daylight View, Still Mode, Noise Reduction, Tv-system, Rgb/ypbpr , Nglish - 33

Get Panasonic PT-LB90NTEA PDF manuals and user guides View all Panasonic PT-LB90NTEA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

PICTURE menu DAYLIGHT VIEW You can keep the projected image bright and vivid even in well-lit rooms where the ambient light sources cannot be controlled, such as when a door opens or when window coverings fail to block out sunlight. Change setting Change setting AUTO ON OFF AUTO ON OFF Automatic adjustment Active Deactive Remarks zzDo not cover the Ambient Luminance Sensor (ALS) of the projector. The AUTO mode may not operate normally. zzAUTO is not available when INSTALLATION in PROJECTOR SETUP menu is set to REAR/DESK or REAR/CEILING. STILL MODE You can reduce the vertical flicker when projecting a still image. (Available with signals of S-VIDEO/VIDEO only) Change setting Change setting OFF ON Deactive Active Note zzYou must set to OFF when projecting a moving image. NOISE REDUCTION You can switch the automatic noise reduction system on/off. (Available with signals of S-VIDEO/VIDEO only) Change setting Change setting OFF ON No noise reduction Automatic noise reduction Note zzNOISE REDUCTION is set active when the selected input signal has less noise. Applying noise reduction may affect the image quality, if so, set to OFF. TV-SYSTEM When the video signal is changed, the setting switches automatically. You can switch the setting manually to match the video data. (Available with signals of S-VIDEO/VIDEO only) Change setting Change setting AUTO NTSC NTSC4.43 SECAM PAL-N PAL-M PAL Note zzAUTO mode is selected by default. zzWhen the projector is not working properly in AUTO mode, change the setting according to each TV system type. Remarks zzAUTO setting will automatically select the compatible signal from NTSC/NTSC 4.43/PAL/PAL60/PAL-M/ PAL-N/SECAM. RGB/YPBPR AUTO mode is selected by default. If the image is not projected normally in the AUTO mode, select RGB or YPBPR according to the input signal. The function becomes effective only when certain signals below are input. (VGA60, 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i, 720/60p, 720/50p) Select the signals to be input to the COMPUTER1 and COMPUTER2 IN terminal. Change setting Change setting AUTO RGB YPBPR Automatic adjustment For RGB signals For YPBPR signals Settings ENGLISH - 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
PICTURE menu
E
NGLISH - 33
Settings
DAYLIGHT VIEW
You can keep the projected image bright and vivid
even in well-lit rooms where the ambient light sources
cannot be controlled, such as when a door opens or
when window coverings fail to block out sunlight.
Change setting
Change setting
AUTO
ON
OFF
AUTO
Automatic adjustment
ON
Active
OFF
Deactive
Remarks
Do not cover the Ambient Luminance Sensor (
z
ALS
)
of the projector. The
AUTO
mode may not operate
normally.
AUTO
z
is not available when
INSTALLATION
in
PROJECTOR SETUP
menu is set to
REAR/DESK
or
REAR/CEILING
.
STILL MODE
You can reduce the vertical flicker when projecting a
still image.
(Available with signals of
S-VIDEO/VIDEO
only)
Change setting
Change setting
OFF
Deactive
ON
Active
Note
You must set to
z
OFF
when projecting a moving
image.
NOISE REDUCTION
You can switch the automatic noise reduction system
on/off.
(Available with signals of
S-VIDEO/VIDEO
only)
Change setting
Change setting
OFF
No noise reduction
ON
Automatic noise reduction
Note
NOISE REDUCTION
z
is set active when the selected
input signal has less noise. Applying noise reduction
may affect the image quality, if so, set to
OFF
.
TV-SYSTEM
When the video signal is changed, the setting
switches automatically. You can switch the setting
manually to match the video data.
(Available with signals of
S-VIDEO/VIDEO
only)
Change setting
Change setting
AUTO
NTSC
NTSC4.43
SECAM
PAL-N
PAL-M
PAL
Note
AUTO
z
mode is selected by default.
When the projector is not working properly in
z
AUTO
mode, change the setting according to each TV
system type.
Remarks
AUTO
z
setting will automatically select the compatible
signal from
NTSC/NTSC 4.43/PAL/PAL60/PAL-M/
PAL-N/SECAM
.
RGB/YP
B
P
R
AUTO
mode is selected by default. If the image is not
projected normally in the
AUTO
mode, select
RGB
or
YP
B
P
R
according to the input signal.
The function becomes effective only when certain
signals below are input.
(VGA60, 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i,
720/60p, 720/50p)
Select the signals to be input to the
COMPUTER1
and
COMPUTER2
IN terminal.
Change setting
Change setting
AUTO
Automatic adjustment
RGB
For RGB signals
YP
B
P
R
For YP
B
P
R
signals