Panasonic PT-LB90NTEA User Manual - Page 52

NGLISH, press▲▼buttons to select LAMP RUNTIME.

Get Panasonic PT-LB90NTEA PDF manuals and user guides View all Panasonic PT-LB90NTEA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Care and Replacement 5555 Attach the lamp unit cover and tighten the 2 lamp unit cover fixing screws securely with a Phillips-head screwdriver. 6666 Connect the mains lead to a mains socket. 7777 Press the POWER button and the projection starts. Remarks zzIf INITIAL START UP in the PROJECTOR SETUP menu is set to ON, the projector starts projecting when the mains lead is connected to a mains socket. (Æpage 41) 8888 Press the MENU button to display the main menu and press▲▼buttons to scroll to the PROJECTOR SETUP menu. 9999 Press the ENTER button to select the PROJECTOR SETUP menu and press▲▼buttons to select LAMP RUNTIME. 11111 Press and hold the ENTER button for approximately 3 seconds. zzThe LAMP RUNTIME confirmation screen is displayed. LAMP RUNTIME LAMP RUNTIME RESET. OK PRESS BUTTON CANCEL PRESS ANY OTHER BUTTON Note zzIf any button other than the POWER button is pressed, the LAMP RUNTIME screen disappears and the lamp runtime is not reset. (Repeat from step 8 again). 11111 Press the POWER button. zzAfter the lamp goes off, projection stops and the POWER button lights in red, then disconnect the mains plug. 11111 The lamp runtime is reset to "0". Maintenance 52 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Care and Replacement
52 -
E
NGLISH
Maintenance
Attach the lamp unit cover and tighten the 2 lamp unit cover fixing screws securely
5 )
with a Phillips-head screwdriver.
Connect the mains lead to a mains socket.
6 )
Press the POWER button and the projection starts.
7 )
Remarks
If
z
INITIAL START UP
in the
PROJECTOR SETUP
menu is set to
ON
, the projector starts projecting when the
mains lead is connected to a mains socket. (
Æ
page 41)
Press the MENU button to display the main menu and press▲▼buttons to scroll to
8 )
the PROJECTOR SETUP menu.
Press the ENTER button to select the PROJECTOR SETUP menu and
9 )
press▲▼buttons to select LAMP RUNTIME.
Press and hold the ENTER button for approximately 3 seconds.
10 )
The
z
LAMP RUNTIME
confirmation screen is displayed.
LAMP RUNTIME
LAMP RUNTIME RESET.
OK
CANCEL
PRESS ANY OTHER BUTTON
PRESS
BUTTON
Note
If any button other than the
z
POWER
button is pressed, the
LAMP RUNTIME
screen disappears and the lamp
runtime is not reset. (Repeat from step 8 again).
Press the POWER button.
11 )
After the lamp goes off, projection stops and the
z
POWER
button lights in red, then disconnect the mains
plug.
The lamp runtime is reset to “0”.
12 )