Panasonic PTAE8000 Operating Instructions - Page 18

Preparation, About your projector, Remote control

Get Panasonic PTAE8000 PDF manuals and user guides View all Panasonic PTAE8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Preparation AAbbouotuyotuyr opruojrecptorrojector Remote control ■■Top Remote control signal transmitter Send remote control signal. Point at the remote control receiver part on the projector when using. ■■Front With the switch of the projector turned , switch between the standby mode and projection mode. Cycle through the [PICTURE MODE]. Display the [VIERA LINK] menu. Display the menu screen. Display menus of external devices when using VIERA Link. Change the operation mode during gamma adjustment. Change the detection level of parallax when the parallax adjustment monitor is displayed (when [Mode3] is set). Switch the input signals. Adjust the zoom and focus. Display the [PICTURE] menu or [ADVANCED MENU] menu. Display the [MEMORY LOAD] menu. Display the input waveform. Display the [3D SETTINGS] menu. Reset adjusted menu values to the default settings. Use for menu screen operation. Allocate frequently used operations and use as a shortcut button. Inserting and removing the remote control batteries Open the cover. Insert the batteries and replace the cover (insert from side). ● Follow the reverse procedure to remove the batteries. Attention zzDo not drop the remote control. zzAvoid contact with liquids or moisture. zzDo not attempt to disassemble or modify the remote control. Note zzPressing buttons on the remote control when button lights is set to on illuminates the button lights. Button lights dim if no actions are carried out after approximately 5 seconds, and then extinguish if no actions are carried out after a further 5 seconds. zzWhen pointed directly at the receiver on the front of the projector, the remote control can be used up to a distance of approximately 7 m (23'). It may also be used at a vertical/horizontal angle of up to ±30 degrees. zzThe remote control may not operate correctly if there is an obstacle between it and the receiver on the projector. Signals from the remote control can be reflected off a screen when using the projector, but limitations to the range of operability may occur due to reflected light loss resulting from the properties of the screen. zzThe remote control may not be usable if the receiver is exposed to fluorescent or other strong lights. As far as is possible, keep the remote control away from light sources. zzWhen viewing 3D images the remote control may not respond well in some cases. ( page 70) 18 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
18 -
ENGLISH
Preparation
Remote control
■
Top
■
Front
Adjust the zoom and focus.
Display the [
MEMORY
LOAD
] menu.
Display the input waveform.
Reset adjusted menu values
to the default settings.
Use for menu screen
operation.
Display the [
3D SETTINGS
]
menu.
Allocate frequently used operations
and use as a shortcut button.
Inserting and removing the remote control batteries
Open the cover.
Insert the batteries and
replace the cover (insert
from
side).
Display the menu screen.
Switch the input signals.
Cycle through the
[
PICTURE MODE
].
Display the [
VIERA LINK
]
menu.
Remote control signal transmitter
Send remote control signal.
Point at the remote control receiver part on the
projector when using.
Attention
z
Do not drop the remote control.
z
Avoid contact with liquids or moisture.
z
Do not attempt to disassemble or modify the remote control.
Note
z
Pressing buttons on the remote control when button lights is set to on illuminates the button lights.
Button lights dim if no actions are carried out after approximately 5 seconds, and then extinguish if no actions are carried
out after a further 5 seconds.
z
When pointed directly at the receiver on the front of the projector, the remote control can be used up to a distance of
approximately 7 m (23'). It may also be used at a vertical/horizontal angle of up to ±30 degrees.
z
The remote control may not operate correctly if there is an obstacle between it and the receiver on the projector.
Signals from the remote control can be reflected off a screen when using the projector, but limitations to the range of
operability may occur due to reflected light loss resulting from the properties of the screen.
z
The remote control may not be usable if the receiver is exposed to fluorescent or other strong lights. As far as is possible,
keep the remote control away from light sources.
z
When viewing 3D images the remote control may not respond well in some cases. (
page 70)
● Follow the reverse
procedure to remove the
batteries.
About your projector
Display menus of external devices
when using VIERA Link.
Change the operation mode during
gamma adjustment.
Change the detection level of parallax
when the parallax adjustment monitor
is displayed (when [Mode3] is set).
With the <MAIN POWER> switch of the
projector turned <ON>, switch between
the standby mode and projection mode.
Display the [
PICTURE
] menu or
[
ADVANCED MENU
] menu.