Panasonic PTAE8000 Operating Instructions - Page 85

Maintenance, TEMP and LAMP Indicators, Managing the indicated problems

Get Panasonic PTAE8000 PDF manuals and user guides View all Panasonic PTAE8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

TEMP and LAMP IndicatoTrEsMP and LAMP Indicators Managing the indicated problems If a problem should occur with the projector, the lamp indicator and/or temperature indicator will illuminate or flash. Check the indicator status and deal with problems as follows. Attention zzWhen switching off power to deal with problems, ensure that you follow the procedure in "Switching off the power". ( page 30) Note zzCheck the status of the power supply with the power indicator . ( page 28)  Temperature indicator Lamp indicator ■■Temperature indicator Indicator status Problem Cause Solution zzIlluminates red during projection. (Alert indicating [REFER TO THE "TEMP indicator" SECTION IN THE OPERATION MANUAL.] is displayed.) zzFlashing red when power is turned off (projection stops automatically). The temperature inside and/or outside the projector is abnormally high. The air intake and The room exhaust ports may temperature may be obstructed. be too high. The air filter unit The projector may be being may be excessively used at high elevations dirty and ventilation (1 400 m (4 593 ft) or more may be poor. above sea level). Remove object(s) from the ventilation ports or clear the area around the projector. Place the projector in an environment with temperature and humidity as designated in the specifications. ( page 106) Clean or replace the air filter unit. ( page 87) The projector can only be used for two minutes after turning on. Set [HIGH ALTITUDE MODE] to [ON] within two minutes of turning the projector on. ( page 80) Note zzIf the indicator is illuminated or flashes despite taking the actions above, please contact your dealer to have your projector repaired. Maintenance ENGLISH - 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
ENGLISH
- 85
Maintenance
TEMP and LAMP Indicators
Managing the indicated problems
If a problem should occur with the projector, the lamp indicator <LAMP> and/or temperature indicator <TEMP>
will illuminate or flash. Check the indicator status and deal with problems as follows.
Attention
z
When switching off power to deal with problems, ensure that you follow the procedure in “Switching off the power”.
(
page 30)
Note
z
Check the status of the power supply with the power indicator <ON (G)/STANDBY (R)>. (
page 28)
Lamp indicator
Temperature indicator
■
Temperature indicator <TEMP>
Indicator
status
z
Illuminates red during projection.
(Alert indicating [REFER TO THE “TEMP indicator” SECTION IN THE OPERATION MANUAL.] is
displayed.)
z
Flashing red when power is turned off (projection stops automatically).
Problem
The temperature inside and/or outside the projector is abnormally high.
Cause
The air intake and
exhaust ports may
be obstructed.
The room
temperature may
be too high.
The air filter unit
may be excessively
dirty and ventilation
may be poor.
The projector may be being
used at high elevations
(1 400 m (4 593 ft) or more
above sea level).
Solution
Remove object(s)
from the ventilation
ports or clear the
area around the
projector.
Place the projector
in an environment
with temperature
and humidity as
designated in the
specifications.
(
page 106)
Clean or replace
the air filter unit.
(
page 87)
The projector can only be
used for two minutes after
turning on.
Set [HIGH
ALTITUDE MODE] to [ON]
within two minutes of turning
the projector on.
(
page 80)
Note
z
If the <TEMP> indicator is illuminated or flashes despite taking the actions above, please contact your dealer to have your
projector repaired.