Panasonic SAXR58 SAXR58 User Guide - Page 39
TROUBLESHOOTING GUIDE, Common problems, s, Surround effects, Radio, Remote control
View all Panasonic SAXR58 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
Troubleshooting guide Troubleshooting guide ENGLISH Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, consult your dealer for instructions. Common problems Pages No power. • Ensure the AC mains lead is connected. 11 No sound. Sound is distorted. • Turn the volume up. • Check connections to speakers and other equipment. • Turn on the speakers. • Select the correct source. • Change DIG INPUT setting to suit the type of connection you have made. • Check that the digital signals can be decoded by this unit. • Turn the muting off. • Turn PCM FIX off. • Recording of some DVD-Audio may not be possible due to copyright protection. 18 5 to 13 18 18 28 19 31 28 - Sound stops. "OVERLOAD" • Determine and correct the cause, then turn the unit on. appears on the display for about a Causes include: second, and the unit turns off. - Shorting (bare wires touching) of positive and negative speaker wires. - - Using speakers with an impedance lower than that rated for this unit. 13 - Straining of the speakers through excessive volume or power. - - Using the unit in a hot environment without proper ventilation. - Consult your dealer if the problem occurs again after switching the unit on. Analogue input becomes distorted • Switch the attenuator on. 29 and the message "OVERFLOW" appears on the display during playback. "F76" appears on the display and • Turn the unit off, disconnect the AC mains lead, and consult your dealer. - the unit turns off. "F70" appears on the display. • Turn the unit off, disconnect the AC mains lead, and consult your dealer. - "REMOTE 2" or "REMOTE 1" • Match the codes on the main unit and the remote control. 37 appears on the display. Display is dim. • Cancel "DIMMER". 31 Clicking sound is heard during play. Surround effects Sound is not heard from the center, surround or subwoofer speakers. • Depending on the input signal when playing DVD etc., the ADVANCED DUAL AMP function changes automatically. A clicking sound is heard when it changes. This does not mean a problem with the unit. ➡You can also set the unit against automatic advanced dual amp operations. • Ensure the speaker settings for your speakers are correct. • Confirm Dolby Pro LogicΙΙx, NEO:6, or SFC settings, and select an adequate mode. • Switch SURROUND on when you play 2-channel stereo sources. - 29 Pages 14 to 17, 27 22 to 25 18 Sound is not heard from the surround back speaker. • Ensure the speaker settings for your speakers are correct. • Switch SURROUND on. 14 to 17, 27 18 Cannot switch SURROUND on. • Check if the center speaker, surround speakers, and surround back speakers are connected properly. 13 (Dolby Pro LogicΙΙx, NEO:6, and • Switch SPEAKERS A on. 18 SFC are unavailable.) • You cannot use the SURROUND effect when the input source contains PCM signals with sampling frequencies - of 192 kHz. • Cancel DVD analogue 6-channel playback. 20 • You cannot use the effect when the input source contains dual audio signals in Dolby Digital or DTS formats. - There is no DTS audio output. • Set the DTS Digital Audio Output setting on the DVD player or DVD recorder to "Bitstream". - There is audio output, but the DTS decoder indicator is not lit. Sound is distorted when using the • Depending on the input source, sound may be distorted if you increase the SFC effect level. If this happens, 25 Sound Field Control (SFC). decrease the SFC effect level. Radio The radio cannot be tuned in or there is a lot of noise and interference. • Connect the appropriate antenna. (You may need an outdoor antenna or one with more elements.) • Adjust the position of the FM or AM antenna. • Reduce the treble. • Turn off nearby televisions, video decks, DVD recorder, DVD player, and satellite receivers. • Separate the antenna from other cables, cords, and appliances. Pages 11 11 31 - There is a lot of noise when • Try changing the BEAT PROOF mode. 33 listening to AM. The correct AM frequency cannot be tuned in. HDMI When using an HDMI connection, the first few seconds of sound is cut off. • Change the frequency step to suit your area when AM is selected. • Should you be playing a chapter on a DVD: - Change the audio output setting on the DVD player or DVD recorder from "Bitstream" to "PCM". (6.1-channel sources will however be played as 5.1-channel.) - Select "PCMFIX" as instructed in "Input signals" when you play 2-channel sources. 32 Pages 28 "U 70-1-1" appears on the display. • The equipment connected by the HDMI cable is not compatible with the unit's copyright protection technology. - "U 70-1-2" appears on the display. • The unit has received a signal for a picture format that is incompatible with the HDMI connection. Check the - settings of the connected equipment. "U 70- 3" appears on the display. • Should anything unusual happen using an HDMI connection: Consult your dealer if the sign remains on the display after these steps. - Turn the connected equipment off and on again. - Pull out the HDMI cable then reinsert it. - Reduce the amount of equipment connected in series to the HDMI terminal if exceeding 2 units. 5, 21 - The unit does not work properly. • The unit does not work properly when wrong cords are in HDMI input and output terminals. Turn the unit off, unplug the AC mains lead, and make connections again. 5, 21 HDAVI Control does not function properly. Remote control The remote control does not work. • Connect the unit to your TV (VIERA) using the HDMI cable, switch the TV on, unplug the unit's AC mains lead, and insert it into a household mains socket again. • Replace the batteries if they are worn. - Pages 3 Other products respond to the remote control. • Change this unit's remote control code to "REMOTE 2". 37 39 RQTV0156