Panasonic TH-50PX600 Operating Instructions - Page 4

Accessories/Options Check you have all the items shown. Accessories □Remote Control •Transmitter EUR7737Z10 □Batteries for the Remote •Control Transmitter (2) AA Battery □Antenna Adapter F-Type •for 5C-2V □Cable clamper (2) □AC cord □IR Blaster □ Pedestal • • • TBL2AX00021 TBL2AX00061 (TH-42PX600U) (TH-50PX600U) TBL2AX00071 (TH-58PX600U) □Operating Instructions □Product Registration Card (U.S.A.) □Customer Care Plan Card (U.S.A.) Installing remote's batteries 1 Open 2 Close Hook Note the correct polarity (+ or -). Caution •Incorrect installation may cause battery leakage and corrosion, resulting in damage to the remote control unit. Do not mix old and new batteries. Do not mix different battery types (such as alkaline and manganese batteries). •• Do not use rechargeable (Ni-Cd) batteries. Do not burn or break batteries. Make a note of the remote control codes before changing batteries in case the codes are reset. (p. 49-50) Optional accessories •Wall-hanging bracket (vertical) TY-WK42PV3U (TH-42PX600U, TH-50PX600U, TH-58PX600U) Wall-hanging bracket •(angle) TY-WK42PR3U (TH-42PX600U, TH-50PX600U) Plasma TV stand TY-S42PX600W • (TH-42PX600U) TY-S50PX600W • (TH-50PX600U) TY-S58PX600W • (TH-58PX600U) Note 6 In order to maintain the unit's performance and safety, be absolutely sure to ask your dealer or a licensed •contractor to secure the wall-hanging brackets. Carefully read the instructions accompanying the plasma TV stand or pedestal, and be absolutely sure to take •steps to prevent the TV from tipping over. Handle the TV carefully during installation since subjecting it to impact or other forces may cause its paneling to • crack. Attaching the pedestal to the plasma television Warning •Do not disassemble or modify the pedestal. Otherwise the unit may fall over and become damaged, and personal injury may result. Caution •Do not use any television or displays other than those given in this manual. Otherwise the unit may fall over and become damaged, and personal injury may result. •Do not use the pedestal if it becomes warped or physically damaged. If you use the pedestal while it is physically damaged, personal injury may result. Contact your nearest Panasonic Dealer immediately. •During setting-up, make sure that all screws are securely tightened. If sufficient care is not taken to ensure screws are properly tightened during assembly, the pedestal will not be strong enough to support the plasma television, and it might fall over and become damaged, and personal injury may result. •Use the accessory fall-prevention brackets to secure the plasma television. If the unit is knocked or children climb onto the pedestal with the Plasma TV installed, the plasma television may fall over and personal injury may result. •Two or more people are required to install and remove the television. If two people are not present, the television may be dropped, and personal injury may result. Accessories for pedestal assembly A Assembly screw (4) B Assembly screw (4) C Pole (2) D Base (1) E Band (2) (for 42˝ and 50˝) M5 x 18 (for 58˝) M5 x 25 M5 x 65 1 Assembling the pedestal Using the four assembly screws A , securely fasten the left and right poles to the base, as shown in the illustration below. Pole () a Front A Pole Pole Pole () b Front Align the stamped marks. 2 Setting-up Television unit Pedestal Align the stamped marks. B B Rear Label * Carry out work on a horizontal and level surface. Lift the television unit above the pedestal base, with the back of the display unit on the same side as the Label. Then align the holes in the television unit with the poles of the pedestal and lower the television unit into place. Use the assembly screws B (M5 x 65) to fasten securely. 7 Quick Start Guide Accessories/Options