Pioneer AXM-P8000 Owner's Manual - Page 22

Introduction of DSP, adjustments, Digital Signal Processor, Operating the DSP menu

Get Pioneer AXM-P8000 - Controller Module PDF manuals and user guides
UPC - 012562693538
View all Pioneer AXM-P8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Section 07 Digital Signal Processor Introduction of DSP adjustments Important ! You can use the following functions only when the remote control is set to DEQ mode. ! Following functions are effective only when you connected a Pioneer multi-channel processor (DEQ-P8000) to this unit. By carrying out the following settings/adjustments in the order shown, you can create a finely-tuned sound field effortlessly. 1 Setting the speaker setting 2 Using the position selector 3 Auto TA and EQ (auto-time alignment and auto- equalizing) 4 Adjusting the time alignment 5 Adjusting the speaker output levels using a test tone 6 Selecting a cross-over frequency 7 Adjusting the speaker output levels 8 Adjusting 3-band parametric equalizer Operating the DSP menu 1 1 DSP display Shows the DSP status. % Press p to display the DSP function names. Press p repeatedly to switch between the following DSP functions: Posi (position selector)Fad (balance adjustment)SLA (source level adjustment)DRC (dynamic range control)DIRECT (direct) Dolby PLB (Dolby Pro Logic B)Downmix (down mix) # To return to the display of each source, press BAND. Notes ! If you do not operate the DSP function within about 30 seconds, the display is automatically returned to the source display. ! If both the center and the rear speakers are set to OFF in the DSP details menu (refer to Setting the speaker setting on page 26), you cannot use Dolby PLB. 22 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Introduction of DSP
adjustments
Important
!
You can use the following functions only when
the remote control is set to
DEQ
mode.
!
Following functions are effective only when
you connected a Pioneer multi-channel pro-
cessor (DEQ-P8000) to this unit.
By carrying out the following settings/adjust-
ments in the order shown, you can create a fi-
nely-tuned sound field effortlessly.
1
Setting the speaker setting
2
Using the position selector
3
Auto TA and EQ (auto-time alignment and auto-
equalizing)
4
Adjusting the time alignment
5
Adjusting the speaker output levels using a
test tone
6
Selecting a cross-over frequency
7
Adjusting the speaker output levels
8
Adjusting 3-band parametric equalizer
Operating the DSP menu
1
1
DSP display
Shows the DSP status.
%
Press
p
to display the DSP function
names.
Press
p
repeatedly to switch between the
following DSP functions:
Posi
(position selector)
µ
Fad
(balance adjust-
ment)
µ
SLA
(source level adjustment)
µ
DRC
(dynamic range control)
µ
DIRECT
(direct)
µ
Dolby PL
B
(Dolby Pro Logic
B
)
µ
Downmix
(down mix)
#
To return to the display of each source, press
BAND
.
Notes
!
If you do not operate the DSP function within
about 30 seconds, the display is automatically
returned to the source display.
!
If both the center and the rear speakers are
set to
OFF
in the DSP details menu (refer to
Setting the speaker setting
on page 26), you
cannot use
Dolby PL
B
.
Digital Signal Processor
En
22
Section
07