Pioneer AXM-P8000 Owner's Manual - Page 35

Adjusting initial settings, Setting the clock, Switching the dimmer setting, Initial Settings

Get Pioneer AXM-P8000 - Controller Module PDF manuals and user guides
UPC - 012562693538
View all Pioneer AXM-P8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Initial Settings Section 08 English Adjusting initial settings 1 Initial settings lets you perform initial setup of different settings for this unit. Important You can use the following functions only when the remote control is set to DEQ mode. 1 Function display Shows the function status. 1 Press SOURCE and hold until the unit turns off. 2 Press o and hold until the clock appears in the display. 3 Press o to select one of the initial settings. Press o repeatedly to switch between the following settings: ClockDimmer (dimmer)Brightness (brightness)Digital ATT (digital attenuation) Tel/Navi (telephone muting/attenuation) AUX (auxiliary setting)Digital1 (digital source 1)Digital2 (digital source 2) Analog1 (analog source 1)Analog2 (analog source 2)Analog3 (analog source 3) Analog4 (analog source 4)Analog5 (analog source 5)Analog6 (analog source 6) Audio Reset (audio reset) # To cancel initial settings, press BAND. # You can also cancel initial settings by holding down o until the unit turns off. Setting the clock Use these instructions to set the clock. 1 Press o to select clock. Press o repeatedly until clock appears in the display. 2 Press m or n to select the segment of the clock display you wish to set. Pressing m or n will select one segment of the clock display: HourMinute As you select segments of the clock display the segment selected will blink. 3 Press q or r to set the clock. Pressing r will increase the selected hour or minute. Pressing q will decrease the selected hour or minute. Switching the dimmer setting To prevent the display from being too bright at night, the display is automatically dimmed when the cars headlights are turned on. You can turn the dimmer on or off. 1 Press o to select Dimmer. Press o repeatedly until Dimmer appears in the display. 2 Press r to turn dimmer on. Dimmer :ON appears in the display. # To turn dimmer off, press q. En 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Adjusting initial settings
1
Initial settings lets you perform initial setup of
different settings for this unit.
Important
You can use the following functions only when
the remote control is set to
DEQ
mode.
1
Function display
Shows the function status.
1
Press SOURCE and hold until the unit
turns off.
2
Press
o
and hold until the clock ap-
pears in the display.
3
Press
o
to select one of the initial set-
tings.
Press
o
repeatedly to switch between the
following settings:
Clock
µ
Dimmer
(dimmer)
µ
Brightness
(brightness)
µ
Digital ATT
(digital attenuation)
µ
Tel/Navi
(telephone muting/attenuation)
µ
AUX
(auxiliary setting)
µ
Digital1
(digital
source 1)
µ
Digital2
(digital source 2)
µ
Analog1
(analog source 1)
µ
Analog2
(ana-
log source 2)
µ
Analog3
(analog source 3)
µ
Analog4
(analog source 4)
µ
Analog5
(ana-
log source 5)
µ
Analog6
(analog source 6)
µ
Audio Reset
(audio reset)
#
To cancel initial settings, press
BAND
.
#
You can also cancel initial settings by holding
down
o
until the unit turns off.
Setting the clock
Use these instructions to set the clock.
1
Press
o
to select clock.
Press
o
repeatedly until clock appears in
the display.
2
Press
m
or
n
to select the segment
of the clock display you wish to set.
Pressing
m
or
n
will select one segment
of the clock display:
Hour
µ
Minute
As you select segments of the clock display
the segment selected will blink.
3
Press
q
or
r
to set the clock.
Pressing
r
will increase the selected hour or
minute. Pressing
q
will decrease the se-
lected hour or minute.
Switching the dimmer setting
To prevent the display from being too bright at
night, the display is automatically dimmed
when the car
±
s headlights are turned on. You
can turn the dimmer on or off.
1
Press
o
to select Dimmer.
Press
o
repeatedly until
Dimmer
appears in
the display.
2
Press
r
to turn dimmer on.
Dimmer :ON
appears in the display.
#
To turn dimmer off, press
q
.
Initial Settings
En
35
English
Section
08