Pioneer AXM-P8000 Owner's Manual - Page 27

Selecting a cross-over, frequency, Digital Signal Processor, Correcting the subwoofer, s phase

Get Pioneer AXM-P8000 - Controller Module PDF manuals and user guides
UPC - 012562693538
View all Pioneer AXM-P8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Digital Signal Processor Section 07 English 1 Press p and hold until SP Set appears in the display. 2 Press m or n to select the speaker to be adjusted. Each press of m or n selects the speaker in the following order: Front speakersCenter speakerRear speakersSubwooferS.W (subwoofer setting) # You can switch to S.W only when the subwoofer has been set to ON. 3 Press q or r to select the correct size for the selected speaker. Each press of q or r selects the size in the following order: LARGE (large)SMALL (small)OFF (off) # You cannot select OFF, when the front speakers have been selected. # You can turn ON or OFF, when the subwoofer has been selected. # You can switch Rev. (reverse phase) or Normal (normal phase), when S.W (subwoofer setting) has been selected. 4 Press BAND to return to the playback display. Correcting the subwoofers phase If trying to boost the bass output of the subwoofer doesnt do much or rather makes you feel that the bass gets more murky, this may indicate that the subwoofers output and bass content you hear over other speakers cancel each other out. To remove this problem, try changing the phase setting for the subwoofer. 1 Press p and hold until SP Set appears in the display. 2 Press m or n to select the subwoofer. Each press of m or n selects the speaker in the following order: Front speakersCenter speakerRear speakersSubwooferS.W (subwoofer setting) 3 Press r to turn the subwoofer output on. 4 Press n to select S.W (subwoofer setting). 5 Press q or r to select the subwoofer output phase. Press r to select Normal (normal phase). Press q to select Rev. (reverse phase). 6 Press BAND to return to the playback display. Note When playing a 2-channel mono source with Pro Logic B turned on, there may be occasions when the following will occur: ! No audio is outputted if the center speaker setting is SMALL or LARGE and no center speaker is installed. ! Audio is heard only over the center speaker if installed and the center speaker setting is SMALL or LARGE. Selecting a cross-over frequency You can select a frequency, under which sounds are reproduced through the subwoofer. If the installed speakers include one whose size has been set to SMALL, you can select a frequency, under which sounds are reproduced through a LARGE speaker or subwoofer. En 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
1
Press
p
and hold until SP Set appears
in the display.
2
Press
m
or
n
to select the speaker
to be adjusted.
Each press of
m
or
n
selects the speaker
in the following order:
Front speakers
µ
Center speaker
µ
Rear speak-
ers
µ
Subwoofer
µ
S.W
(subwoofer setting)
#
You can switch to
S.W
only when the subwoo-
fer has been set to
ON
.
3
Press
q
or
r
to select the correct size
for the selected speaker.
Each press of
q
or
r
selects the size in the
following order:
LARGE
(large)
µ
SMALL
(small)
µ
OFF
(off)
#
You cannot select
OFF
, when the front speak-
ers have been selected.
#
You can turn
ON
or
OFF
, when the subwoofer
has been selected.
#
You can switch
Rev.
(reverse phase) or
Normal
(normal phase), when
S.W
(subwoofer
setting) has been selected.
4
Press BAND to return to the playback
display.
Correcting the subwoofer
±
s phase
If trying to boost the bass output of the sub-
woofer doesn
±
t do much or rather makes you
feel that the bass gets more murky, this may
indicate that the subwoofer
±
s output and bass
content you hear over other speakers cancel
each other out. To remove this problem, try
changing the phase setting for the subwoofer.
1
Press
p
and hold until SP Set appears
in the display.
2
Press
m
or
n
to select the subwoo-
fer.
Each press of
m
or
n
selects the speaker
in the following order:
Front speakers
µ
Center speaker
µ
Rear speak-
ers
µ
Subwoofer
µ
S.W
(subwoofer setting)
3
Press
r
to turn the subwoofer output
on.
4
Press
n
to select S.W (subwoofer set-
ting).
5
Press
q
or
r
to select the subwoofer
output phase.
Press
r
to select
Normal
(normal phase).
Press
q
to select
Rev.
(reverse phase).
6
Press BAND to return to the playback
display.
Note
When playing a 2-channel mono source with Pro
Logic
B
turned on, there may be occasions when
the following will occur:
!
No audio is outputted if the center speaker
setting is
SMALL
or
LARGE
and no center
speaker is installed.
!
Audio is heard only over the center speaker if
installed and the center speaker setting is
SMALL
or
LARGE
.
Selecting a cross-over
frequency
You can select a frequency, under which
sounds are reproduced through the subwoo-
fer. If the installed speakers include one whose
size has been set to
SMALL
, you can select a
frequency, under which sounds are repro-
duced through a
LARGE
speaker or subwoo-
fer.
Digital Signal Processor
En
27
English
Section
07