Pioneer AXM-P8000 Owner's Manual - Page 41

Troubleshooting, Error messages, Additional Information, When problems occur with disc playback

Get Pioneer AXM-P8000 - Controller Module PDF manuals and user guides
UPC - 012562693538
View all Pioneer AXM-P8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Additional Information Appendix English Troubleshooting Common Symptom Cause Action (See) Power doesnt turn on. The unit doesnt operate. Leads and connectors are incorrectly connected. Confirm once more that all connections are correct. The fuse is blown. Rectify the reason for the fuse blowing, then replace the fuse. Be very sure to install the correct fuse with the same rating. Noise and other factors are causing Turn the unit off and then on. the built-in microprocessor to operate incorrectly. Operation with the remote con- The remote control operation mode trol isnt possible. is incorrect. The unit does not operate cor- The remote control code is incor- rectly even when the appropriate remote control buttons are rect. pressed. Battery power is low. Switch to the correct remote control mode. (Page 7) Make sure the remote control selection switch setting and code type setting are the same. (Page 39) Load new battery. (Page 7) No sounds are heard. The volume level will not rise. Cables are not connected correctly. Connect the cables correctly. There is no sound. Volume level is low. The volume level is low. The attenuator is on. Adjust the volume level. Turn the attenuator off. Error messages When problems occur with disc playback, an error message appears on the display. Refer to the table below to identify the problem, then take the suggested corrective action. If the error persists, contact your dealer or your nearest PIONEER Service Center. Error messages Message ERROR-02 TEMP ERROR-10 NON PLAY Cause Action (See) Dirty disc Clean disc. Scratched disc Replace disc. The temperature of this unit is out- Wait until the units temperature returns to side the normal operating range within normal operating limits. The disc does not have the same re- Replace the DVD video with one bearing the gion number as this unit correct region number. This type of disc cannot be played Replace the disc with one this unit can play. by this unit The disc is loaded upside down Check that the disc is loaded correctly. En 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Troubleshooting
Common
Symptom
Cause
Action (See)
Power doesn
±
t turn on.
The unit doesn
±
t operate.
Leads and connectors are incor-
rectly connected.
Confirm once more that all connections are
correct.
The fuse is blown.
Rectify the reason for the fuse blowing, then
replace the fuse. Be very sure to install the
correct fuse with the same rating.
Noise and other factors are causing
the built-in microprocessor to oper-
ate incorrectly.
Turn the unit off and then on.
Operation with the remote con-
trol isn
±
t possible.
The unit does not operate cor-
rectly even when the appropriate
remote control buttons are
pressed.
The remote control operation mode
is incorrect.
Switch to the correct remote control mode.
(Page 7)
The remote control code is incor-
rect.
Make sure the remote control selection
switch setting and code type setting are the
same. (Page 39)
Battery power is low.
Load new battery. (Page 7)
No sounds are heard.
The volume level will not rise.
Cables are not connected correctly.
Connect the cables correctly.
There is no sound.
Volume level is low.
The volume level is low.
Adjust the volume level.
The attenuator is on.
Turn the attenuator off.
Error messages
When problems occur with disc playback, an error message appears on the display. Refer to the
table below to identify the problem, then take the suggested corrective action. If the error persists,
contact your dealer or your nearest PIONEER Service Center.
Error messages
Message
Cause
Action (See)
ERROR-02
Dirty disc
Clean disc.
Scratched disc
Replace disc.
TEMP
The temperature of this unit is out-
side the normal operating range
Wait until the unit
±
s temperature returns to
within normal operating limits.
ERROR-10
The disc does not have the same re-
gion number as this unit
Replace the DVD video with one bearing the
correct region number.
NON PLAY
This type of disc cannot be played
by this unit
Replace the disc with one this unit can play.
The disc is loaded upside down
Check that the disc is loaded correctly.
Additional Information
En
41
English
Appendix