Pioneer DEH-P8300UB Owner's Manual - Page 10

Section 02 Operating this unit Operating this unit Advanced operations using special buttons Pausing playback Press 2/PAUSE to pause or resume. Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 1/S.Rtrv to cycle between: OFF (off)-1-2 1 is effective for low compression rates, and 2 is effective for high compression rates. Storing song information (Bookmark) 1 Press TAG to display the setting mode. 2 Push M.C. left or right to change the mode; press to select. ! SONG - to add information for the song currently playing to bookmarks ! ARTIST - to add artist information for the song currently playing to bookmarks Function settings 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. 3 Turn M.C. to select the function. After selecting, perform the following procedures to set the function. BOOK MARK (bookmark) 1 Push M.C. left or right to change the mode; press to select. For details, refer to Storing song information (Bookmark) on this page. Pause (pause) 1 Press M.C. to pause or resume. Sound Retriever (sound retriever) 1 Press M.C. to select the desired setting. For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on this page. Audio Adjustments 1 1 Audio display Shows the audio adjustment status. 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select AUDIO. 3 Turn M.C. to select the audio function. After selecting, perform the following procedures to set the audio function. Fader/Balance (fader/balance adjustment) 1 Push M.C. up or down to adjust the front/rear speaker balance. ! The front/rear speaker balance cannot be adjusted when the rear output setting is Rear SP :S/W. Refer to S/W control (rear output and subwoofer setting) on the next page. 2 Push M.C. left or right to adjust the left/right speaker balance. Powerful (equalizer recall) 10 En 1 Push M.C. left or right to select an equalizer curve. Powerful-Natural-Vocal-Custom1-Custom2-Flat-Super bass 100 Hz (equalizer adjustment) You can adjust the currently selected equalizer curve setting as desired. Adjusted equalizer curve settings are stored in Custom1 or Custom2. ! A separate Custom1 curve can be created for each source. If you make adjustments when a curve other than Custom2 is selected, the equalizer curve settings will be stored in Custom1. ! A Custom2 curve that is common for all sources can be created. If you make adjustments when the Custom2 curve is selected, the Custom2 curve will be updated. 1 Recall the equalizer curve you want to adjust. 2 Push M.C. left or right to select the equalizer band to adjust. 100Hz-315Hz-1.25kHz-3.15kHz-8kHz 3 Push M.C. up or down to adjust the equalizer curve. +6 to -6 is displayed as the equalizer curve is increased or decreased. LOUD (loudness) Loudness compensates for deficiencies in the lowand high-frequency ranges at low volume. 1 Press M.C. to turn loudness on or off. 2 Push M.C. left or right to select the desired set- ting. Low (low)-Mid (mid)-High (high) Sub W.1 (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to turn subwoofer output on or off. 2 Push M.C. left or right to select the phase of subwoofer output. Push M.C. left to select reverse phase and Reverse appears in the display. Push M.C. right to select normal phase and Normal appears in the display. Sub W.2 (subwoofer adjustment) The cut-off frequency and output level can be adjusted when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer. 1 Push M.C. left or right to select the cut-off fre- quency. 50Hz-63Hz-80Hz-100Hz-125Hz 2 Push M.C. up or down to adjust the output level of the subwoofer. Each time M.C. is pushed up or down, subwoofer level increases or decreases. +6 to -24 is displayed as the level is increased or decreased. Bass (bass boost) 1 Push M.C. up or down to select a desired level. 0 to +6 is displayed as the level is increased or decreased. HPF (high pass filter adjustment) When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press M.C. to turn high pass filter on or off. 2 Push M.C. left or right to select the cut-off fre- quency. 50Hz-63Hz-80Hz-100Hz-125Hz