Pioneer VSX-43TX Owner's Manual - Page 39
NORMAL. Press the ENTER button.
![]() |
View all Pioneer VSX-43TX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
Setting Up for Surround Sound SURROUND SET UP CHANNEL LEVEL (channel balance) The following steps show you how to balance the sound output level of your speakers. Proper speaker balance is essential for obtaining high quality surround sound. If continuing from SPEAKER SETTING go to step 2. MENU TUNER EDIT TOP MENU SYSTEM SETUP ST TUNE GUIDE ST ENTER AUDIO TUNE RETURN 1-6 1-6 STANDBY/ON MOVIE MUSIC ENTER MULTI JOG STANDBY MULTI JOG CONTROL SET UP RETURN SIGNAL HI-BIT SELECT HI-SAMPLING SB CH MODE MIDNIGHT LOUDNESS BAND PHONES SPEAKERS TONE TONE CONTROL BASS/TREBLE Follow steps 1-3 on page 34, if necessary, to get to the starting point mentioned here. 1 Use the 5∞ buttons to select NORMAL. Press the ENTER button. 2 CHANNEL LEVEL should be selected. If it isn't use the 5∞ buttons to select and press ENTER. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B 3 There are two ways to set the CHANNEL LEVEL: MANUAL or AUTO. Select a setting mode with the 5∞ buttons and press ENTER. Test tones will be output. WARNING : Be prepared! The test tones are output at a high volume level. MASTER VOLUME rotates to the reference position (0 dB) and the display on the receiver flashes TEST TONE. After a few seconds the test tone is output. MANUAL: move the test tone manually and adjust the channel level. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B AUTO: the test tone moves by itself and you adjust the levels. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B 4 Adjust the speaker level with the below instructions for the method you chose. Adjust the channel level from -10 dB to +10 dB in 0.5 dB increments. The default setting is 0 dB. In MANUAL (manual test tone) mode To switch the test tone between each speaker use the 5∞ buttons and push ENTER. Adjust the level of each speaker using the 5∞ buttons and ENTER. When done go to step 5. In AUTO (automatic test tone) mode This mode switches the test tone between each speaker automatically. The test tone output cycles through the speakers in the following order: FRONT L SUB WOOFER CENTER SURROUND L FRONT R SURRBACK L SURROUND R SURRBACK R Adjust the level of each speaker using the 5∞ buttons as the test tone is emitted and wait for it to move to the next speaker. When done go to step 6. If you want to change a setting before proceeding you need to complete the procedure and start over from step 1. 5 When you have the levels you want press ENTER. EXIT should be selected (if it isn't select it with the 5∞ buttons). 6 Press ENTER. Next, proceed to CHANNEL DELAY next page. If you want to change a setting before proceeding start over from step 2. memo • If your subwoofer has a volume control, set it to the middle position before doing these operations. • If you are using a Sound Pressure Level (SPL) meter take the readings from your main listening position and adjust the level of each speaker to 75dB SPL (C-weighting/slow reading). • The volume of the subwoofer test tone tends to sound lower than it actually is. You may need to adjust the level after testing your system with an actual soundtrack. 39
![](/manual_guide/products/pioneer-vsx43tx-owners-manual-d621145/39.png)