Pioneer VSX-43TX Owner's Manual - Page 81
FINE CH LEVEL should
View all Pioneer VSX-43TX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 81 highlights
Fine Tuning Your System FINE CHANNEL LEVEL The following steps show you how to balance the sound output level of your speakers more finely than in the NORMAL setup (see page 36). Proper speaker balance is essential for obtaining high quality surround sound and the better the speaker balance the better surround sound you can get. Do this procedure if you want to try and get even finer surround sound. The main difference with this setup method and the CHANNEL LEVEL setup method in NORMAL setup is that here the test tone alternates between the front left speaker (which is used as the reference channel) and the target speaker (that is, the speaker whose level you want to adjust). Listen to the two tones and try to make them the same volume. MASTER VOLUME MENU TUNER EDIT TOP MENU SYSTEM SETUP ST TUNE GUIDE ST ENTER AUDIO TUNE RETURN − + CHANNEL DTV ON/OFF BAND CHANNEL D.ACCESS MPX CLASS 1-5 1-5 STANDBY/ON MOVIE MUSIC ENTER MULTI JOG STANDBY MULTI JOG CONTROL SET UP RETURN SIGNAL HI-BIT SELECT HI-SAMPLING SB CH MODE MIDNIGHT LOUDNESS BAND PHONES SPEAKERS TONE TONE CONTROL BASS/TREBLE Follow steps 1-5 on page 79, if necessary, to get to the starting point mentioned here. 1 FINE CH LEVEL should be selected, if it isn't use the 5∞ buttons to select it. Press ENTER. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH DSP Hi-BIT/ SAMPLING MULTI-ROOM AUTO ON OFF MOVIE MUSIC L C R LFE LS S RS SP A B 2 Use the 5∞ buttons to select the channel you want to adjust. Press ENTER. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B Test tones will be output. WARNING : Be prepared! The test tones are output at a high volume level. MASTER VOLUME rotates to the reference position (0 dB) and the display on the receiver flashes TEST TONE. After a few seconds the test tone is output. The adjustable channels are: R (Front right), C (Center), LS (Surround left), RS (Surround right), SBL (Surround back left), SBR (Surround back right) and SW (Subwoofer). 3 Adjust the level of the channel using the 5∞ buttons. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B Try to get the volume level of the target speaker to match that of the front left speaker, which is the reference in this setup. The levels can be set within a range of -10 dB to +10 dB in 0.5 dB steps. When you press ENTER you will automatically go to the next channel. 4 Press ENTER to select a new channel. Repeat step 3 for every channel. If you want to change a setting before proceeding Use the 5∞ buttons to go back to the channel you want to adjust and press ENTER. Then follow step 3. 5 When done select EXIT (if it's not already selected) and press ENTER. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B Next, if you want, proceed to FINE CHANNEL DELAY. EXPERT 81