Pioneer VSX-43TX Owner's Manual - Page 76

Fine Tuning Your System Assigning the Digital Inputs If you did not hook up your digital equipment in accordance with the default settings for the digital inputs (see page 16,18 & 21) you need to complete the procedure below. You have to do this in order to tell the receiver what digital equipment is hooked up to which terminal so the buttons on the remote correspond to what you have hooked up. 2 DVD/LD TV / SAT VCR/DVR TV CONT VCR 2 CD TUNER MOVIE MUSIC ACOUSTIC EQ RECEIVER INPUT SURROUND MODE SB CH MULTI CH MODE INPUT STEREO/ DIRECT ENTER MIDNIGHT MUTE MASTER VOLUME MENU TUNER EDIT TOP MENU SYSTEM SETUP ST TUNE GUIDE ST ENTER AUDIO TUNE RETURN 1 3-9 3-9 2 RETURN button STANDBY/ON MOVIE MUSIC ENTER MULTI JOG STANDBY MULTI JOG CONTROL SET UP RETURN SIGNAL HI-BIT SELECT HI-SAMPLING SB CH MODE MIDNIGHT LOUDNESS BAND PHONES SPEAKERS TONE TONE CONTROL BASS/TREBLE (If you are continuing from page 74 you can skip the first two steps.) 1 Turn on the receiver, press the RECEIVER button on the remote control. 2 Press the SYSTEM SETUP button. 5 Use the 5∞ buttons to move through the different digital input settings and press the ENTER button. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B The available digital input settings are: DIGI-1: TV/SAT, DIGI-2: CD-R, DIGI-3: DVD/LD, DIGI-4: CD The selected setting will blink. 6 Use the 5∞ buttons select the component that you hooked up to that digital in. Press the ENTER button. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B If you're not sure which component is connected to which digital in, look on the back of the receiver and check the cables you connected. 7 Repeat steps 5-6 to change other digital input settings. 8 When you're finished use the 5∞ buttons to select EXIT and press ENTER. This exits the DIGITAL-IN SELECT mode. 3 Looking at the display on your receiver, use the 5∞ buttons to select INPUT ASSIGN. Press the ENTER button. SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH AUTO ON OFF DSP MOVIE MUSIC Hi-BIT/ SAMPLING MULTI-ROOM L C R LFE LS S RS SP A B 4 DIGITAL-IN should be selected, if not use the 5∞ buttons to select it. Press the ENTER button. 76 SIGNAL PRO LOGIC Neo :6 LOUDNESS AUTO DIGITAL MIDNIGHT TONE DNR ATT STEREO MONO TUNED RF ATT dB RF DTS ES EX RDS EON DIGITAL MPEG AAC ANALOG STEREO SB CH DSP Hi-BIT/ SAMPLING MULTI-ROOM AUTO ON OFF MOVIE MUSIC L C R LFE LS S RS SP A B 9 Use the 5∞ buttons to select EXIT and press ENTER, again. Then, use the 5∞ buttons to select EXIT and press ENTER. This exits the SYSTEM SETUP mode and returns to normal operation. memo • The possible digital inputs that can be assigned are: DVD/LD, TV/SAT, VCR1, VCR2, CD, CD-R, MD. • If you assign a digital input to a certain function (for example DVD/LD) then any digital inputs previously assigned to that function will automatically be set to OFF. This is because one function cannot be assigned to two different places.