Pioneer VSX-92TXH Owner's Manual - Page 60

08 Other connections 60 En • Connect a TV monitor to the MULTI-ZONE & SOURCE MONITOR OUT jacks on the rear of this receiver. You should have a pair of speakers attached to the surround back speaker terminals as shown below. Sub zone Main zone MULTI-ZONE & SOURCE /REC SEL OUT1 ZONE3 OUT2 LAN (10/100) OPTICAL IN 1 (TV/SAT) IN 2 (BD) IN 3 (DVR/ VCR 1) IN 4 (CD-R) 14 ASSIGNABLE IN 1 1 2 (DVD/ LD) IN 2 (CD) COAXIAL IN HDMI IN 1 IN 2 IN 3 IN 1 MAIN IN 2 ZONE2 CONTROL IN OUT IN 1 Y (DVD/ LD) PB MULTI-ZONE & SOURCE IR OUT IN 1 (DVD/LD) IN 2 (BD) ASSIGNABLE 12 OUT Y PB ANTENNA FM UNBAL 75 Ω AM LOOP ZONE2 MULTI-ZONE & SOURCE R ZONE2 L AUDIO PHONO IN CD OUT IN MONITOR MONIOUT TOR OUT DVD/LD IN BD IN TV/SAT IN 1 IN VIDEO / IN 2 GAME 1 IN OUT CD-R/ TAPE/ MD IN R R SUB W. PRE OUT R L FRONT SUB W. CENTER SURROUND R L L FRONT CENTER SURROUND BACK (Single) L SIRIUS IN SPEAKERS IN A FRONT R L PR IN 4 IN 2 Y (BD) PR IN 3 Y OUT DVR/ VCR 1 IN SURROUND R iPod L PB PB OUT OUT DVR/ VCR 2 SURROUND BACK XM PR PR IN RS-232C ASSIGNABLE 14 DIGITAL (VIDEO/GAME 1) ASSIGNABLE 1 3 COMPONENT VIDEO S-VIDEO VIDEO R L AUDIO 1 2 12 V TRIGGER (DC OUT 12V/ TOTAL 50 mA MAX) MULTI CH IN CENTER AC OUTLET SWITCHED 100 W(0.8 A) MAX SURROUND R L R SURROUND BACK / B L(Single) SELECTABLE Using the MULTI-ZONE controls The following steps use the front panel controls to adjust the sub zone volume and select sources.2 See MULTIZONE remote controls below. SPEAKERS AUDIO PARAMETER VIDEO (TUNE) PHONES (ST) ENTER (ST) TUNER EDIT BAND MULTI - ZONE & SOURCE/REC SEL CONTROL ON/OFF SIGNAL SB ch STEREO/ SELECT PROCESSING F.S.SURR MCACC USB SETUP MIC VIDEO/GAME 2 INPUT SETUP (TUNE) RETURN DIGITAL IN S-VIDEO VIDEO L AUDIO R STANDBY/ON INPUT SELECTOR PHASE CONTROL ADVANCED MCACC PHASE CONTROL MCACC AUTO SURR/ POSITION STREAM DIRECT DIGITAL PRECISION PROCESSING DIGITAL VIDEO SCALER HDMI HOME THX STANDARD ADVANCED SURROUND SURROUND VSX-94TXH MASTER VOLUME MULTI-ZONE & SOURCE IR OUT FM UNBAL 75 Ω ZONE2 MULTI-ZONE & SOURCE ZONE2 CONTROL IN 1 (DVD/LD) IN 2 (BD) ASSIGNABLE 12 MONITOR MONIOUT TOR OUT DVD/LD UND L R SURROUND BACK / B L(Single) SELECTABLE Secondary MULTI-ZONE setup (ZONE 3) • Connect a separate amplifier to the OUT1 ZONE3 digital output on the rear of this receiver. The amplifier must have an optical digital input to make this connection. This will allow you to hear the digital output of a component in a second sub zone.1 Sub zone (ZONE 3) MULTI-ZONE & SOURCE /REC SEL OUT1 ZONE3 OUT2 LAN (10/100) IN 1 MAIN IN 2 HDMI ZONE2 Main zone DIGITAL IN MULTI-ZONE & SOURCE /REC SEL OUT1 ZONE3 OUT2 LAN (10/100) OPTICAL IN 1 (TV/SAT) IN 2 (BD) IN 3 (DVR/ VCR 1) IN 4 (CD-R) 14 ASSIGNABLE IN 1 1 2 (DVD/ LD) IN 2 (CD) COAXIAL IN HDMI IN 1 IN 2 IN 3 IN 1 MAIN IN 2 ZONE2 CONTROL IN OUT IN 1 Y (DVD/ LD) PB MULTI-ZONE & SOURCE IR OUT IN 1 (DVD/LD) IN 2 (BD) ASSIGNABLE 12 OUT Y PB ANTENNA P FM UNBAL 75 Ω AM LOOP I ZONE2 MULTI-ZONE & SOURCE ZONE2 R L C OUT I MONITOR MONIOUT TOR OUT DVD/LD IN O BD IN C TA M TV/SAT IN 1 IN I VIDEO / IN 2 GAME 1 IN S PR IN 4 IN 2 Y (BD) PR IN 3 Y OUT DVR/ VCR 1 S R IN PB PB OUT OUT DVR/ VCR 2 XM PR PR IN ASSIGNABLE 14 DIGITAL (VIDEO/GAME 1) ASSIGNABLE 1 3 COMPONENT VIDEO S-VIDEO VIDEO R L AUDIO 1 Press the MULTI-ZONE & SOURCE ON/OFF button on the front panel. Each press selects a MULTI-ZONE option: • ZONE 2 ON - Selects your primary (ZONE 2) sub zone • ZONE 2&3 ON - Select both sub zones • ZONE 3 ON - Selects your secondary (ZONE 3) sub zone • MULTI ZONE OFF - Switches the MULTI-ZONE feature off The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON. 2 Press CONTROL to select the sub zone(s) you want.3 If you selected ZONE 2&3 ON above, you can toggle between ZONE 2 and ZONE 3. • When the receiver is on,4 make sure that any operations for the sub zone are done while ZONE and your selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone only. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 CD-R sends the source connected to the CD-R inputs to the primary (ZONE 2) sub room. • If you select TUNER, you can use the TUNER controls to select a preset station (see Saving station presets on page 35 if you're unsure how to do this).5 Note 1 Only one sub zone is possible if you connect the OUT1 ZONE3 digital output to your second sub zone. 2 When you use ZONE 2, you must set ZONE 2 / RECSEL Setting in the ZONE Audio Setup menu to ZONE 2 (page 69). 3 Note that when recording, this also selects the RECOUT input source. See Making an audio or a video recording on page 73 for more on this. 4 If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show in the display. 5 The tuner cannot be tuned to more than one station at a time. Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not to change stations when recording a radio broadcast.