Samsung NA24T4230FS/AA Installation Guide - Page 23

Converting the pressure regulator, pressure regulator

Get Samsung NA24T4230FS/AA PDF manuals and user guides View all Samsung NA24T4230FS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Installation instructions Required tools Adjustable wrench 1/2" open-end wrench Screwdrivers: Phillips Converting the pressure regulator NOTE If you are using LP gas to fuel the cooktop, the following steps and conversions must be made before the flames can be adjusted. 1. Using adjustable wrench, turn the cap. And carefully look at the spring retainer to locate the NAT or LP position. Small flat-bladed precision screwdriver Nut drivers: 9/32" or 7 mm To convert your cooktop for use with LP gas, perform the following steps and procedures: 1. Disconnect electrical power to the cooktop. Unplug the cooktop power cord, trip the circuit breaker, or remove the fuse from the fuse box. 2. Shut off the gas supply to the cooktop. Close the manual shut-off valve to the cooktop. NAT NAT. Position Cap gas setting nut L.P./Propane LP Position Pressure Regulator 2. The pressure regulator valve is set to NAT display by default when it leaves the factory. Use your fingers to unscrew the gas setting nut, then turn it over to the position of the LP display, install it on the cap with your fingers, and tighten it. 3. Screw the cap back onto the regulator and tighten. Installation instructions 23 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
23
English
Installation instructions
Installation instructions
Required tools
Adjustable wrench
1
/
2
” open-end wrench
Screwdrivers: Phillips
Small flat-bladed
precision screwdriver
Nut drivers:
9
/
32
” or
7 mm
To convert your
cooktop
for use with LP gas, perform the following steps and procedures:
1.
Disconnect electrical power to the cooktop.
Unplug the cooktop power cord, trip
the circuit breaker, or remove the fuse from the fuse box.
2.
Shut off the gas supply to the cooktop.
Close the manual shut-off valve to the
cooktop.
NOTE
If you are using LP gas to fuel the cooktop, the following steps and conversions
must be made before the flames can be adjusted.
1.
Using
adjustable wrench
, turn the cap. And carefully look at the spring retainer
to
locate the NAT or LP position.
Cap
gas setting nut
L.P./Propane
NAT
LP
Position
NAT. Position
Pressure Regulator
2.
The pressure regulator valve is set to NAT display by default when it leaves the
factory. Use your fingers to unscrew the gas setting nut, then turn it over to the
position of the LP display, install it on the cap with your fingers, and tighten it.
3.
Screw the cap back onto the regulator and tighten.
Converting the
pressure regulator