Sharp NP-PH3501QL User Manual - NEC - Page 13

Clearance for Installing the Projector, Example 1 - If there are walls on both sides of the projector.

Get Sharp NP-PH3501QL PDF manuals and user guides View all Sharp NP-PH3501QL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Important Information Clearance for Installing the Projector Allow ample clearance between the projector and its surroundings as shown below. The high temperature exhaust coming out of the device may be sucked into the device again. Avoid installing the projector in a place where air movement from the HVAC is directed at the projector. Heated air from the HVAC can be taken in by the projector's intake vent. If this happens, the temperature inside the projector will rise too high causing the over-temperature protector to automatically turn off the projectors power. Intake vent Exhaust vent Intake vent Intake vent Exhaust vent Exhaust vent Example 1 - If there are walls on both sides of the projector. 60 cm/23.6" or greater 60 cm/23.6" or greater NOTE: • The drawing shows the proper clearance required for the front, back, and top of the projector. • The above drawing can also be applied to the required clearance between intake vent and the floor for the portrait projection. • See page 154 for an installation example on portrait projection. Example 2 - If there is a wall behind the projector. (1) For floor installation: 70 cm/27.6" or greater Lens NOTE: • The drawing shows the proper clearance required for the right, left, and top of the projector. xi

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
xi
Important Information
Clearance for Installing the Projector
Allow ample clearance between the projector and its surroundings as shown below.
The high temperature exhaust coming out of the device may be sucked into the device again.
Avoid installing the projector in a place where air movement from the HVAC is directed at the projector.
Heated air from the HVAC can be taken in by the projector's intake vent. If this happens, the temperature inside the
projector will rise too high causing the over-temperature protector to automatically turn off the projectors power.
Intake vent
Exhaust vent
Intake vent
Intake vent
Exhaust vent
Exhaust vent
Example 1 – If there are walls on both sides of the projector.
60 cm/23.6" or greater
60 cm/23.6" or greater
NOTE:
• The drawing shows the proper clearance required for the front, back, and top of the projector.
• The above drawing can also be applied to the required clearance between intake vent and the floor for the portrait projection.
• See page
154
for an installation example on portrait projection.
Example 2 – If there is a wall behind the projector.
(1) For floor installation:
70 cm/27.6" or greater
Lens
NOTE:
• The drawing shows the proper clearance required for the right, left, and top of the projector.