Sharp XG-C55X XG-C55X Operation Manual - Page 90

Removing and Installing the Lamp Unit, put the projector into - user manual

Get Sharp XG-C55X - Conference Series XGA LCD Projector PDF manuals and user guides
UPC - 074000364219
View all Sharp XG-C55X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Regarding the Lamp Removing and Installing the Lamp Unit Info • Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. (Only the silver screws are loosened). • Please refer to the installation manual included with the lamp unit. 1 Press STANDBY on the projector or on the remote control to put the projector into the standby mode. • Wait until the cooling fan stops. Warning! • Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury. 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). 3 Change the air filter. • Change the air filter whenever you install the lamp unit (see pages 81 and 82). 4 Remove the lamp unit cover. • Loosen the user service screw that secures the lamp unit cover. Then open the cover in the direction of the arrow. -86 Lamp unit BQC-XGC55X//1 STANDBY button STANDBY button AC socket User service screw

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Lamp
unit
BQC-XGC55X//1
User service screw
Removing and Install-
ing the Lamp Unit
Info
•
Be sure to remove the lamp unit by the
handle. Be sure not to touch the glass
surface of the lamp unit or the inside of
the projector.
•
To avoid injury to yourself and damage
to the lamp, be sure to carefully follow
the steps below.
•
Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened).
•
Please refer to the installation manual
included with the lamp unit.
1
Press
STANDBY
on the projector
or
on the remote control to
put the projector into the
standby mode.
•
Wait until the cooling fan stops.
Warning!
•
Do not remove the lamp unit from the
projector right after use. The lamp will
be very hot and may cause burn or
injury.
2
Disconnect the power cord.
•
Unplug the power cord from the AC
socket.
•
Leave the lamp until it has fully cooled
down (about 1 hour).
3
Change the air filter.
•
Change the air filter whenever you in-
stall the lamp unit (see pages
81
and
82
).
4
Remove the lamp unit cover.
•
Loosen the user service screw that
secures the lamp unit cover. Then
open the cover in the direction of the
arrow.
-86
Regarding the Lamp
AC socket
STANDBY button
STANDBY
button