Sharp XG-C55X XG-C55X Operation Manual - Page 93
(RS-232C) Specifications and Command Settings, PC control, Communication conditions, Basic format
UPC - 074000364219
View all Sharp XG-C55X manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 93 highlights
(RS-232C) Specifications and Command Settings PC control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 22 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: 9,600 bps Stop bit: 1 bit Data length: 8 bits Flow control: None Basic format Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer. Command format C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH) Command 4-digit Response code format Normal response Parameter 4-digit Problem response (communication error or incorrect command) O K Return code (0DH) E R R Return code (0DH) Info • When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified. • To conserve power in STANDBY mode, the CPU in this model will enter Deep Sleep mode approximately 10 seconds after the last command is received. In the case of transmitting commands during Deep Sleep mode, it takes a maximum of 30 seconds until the response code is received. If subsequent commands are sent to the projector within 10 seconds, the projector will reply immediately. If no further commands are received within 10 seconds, the projector will again return to Deep Sleep mode. Please note that Deep Sleep mode is only activated in STANDBY mode. There is no delayed RS-232C response when the projector is in operation. • Special commands, "POWR????" and "TLPS_ _ _1" are available for applications that require continuous polling. These commands will not wake the CPU in Deep Sleep mode and the projector will provide immediate reply in STANDBY mode. "1" will indicate Power on, "0" will indicate STANDBY mode. When the power is turned on during standby with the "POWER ON" command, wait for at least 40 seconds after the power has been turned on, and then transmit the next command. • We suggest disabling the AUTO SEARCH feature before initiating RS-232C communications. If AUTO SEARCH is enabled, it will be necessary to send the STANDBY mode command "POWR_ _ _0" two times to power down the projector. (The first "POWR_ _ _0" command cancels AUTO SEARCH and the second "POWR_ _ _0" command will put the projector into the standby mode.) Note • Do not repeatedly or periodically send any commands other than "POWR????" and "TLPS_ _ _1" in STANDBY mode as it will cause problems. • When the projector is put into the standby mode, a message "Shutting Down. Please Wait." is displayed for about 20 seconds. At that time, if the "POWR_ _ _1" command is being sent, "ERR" will be returned and this command is not received. • When using the computer control function of the projector, the adjustment values cannot be read by the computer. Therefore, confirm the values by transmitting the display commands (e.g. "RARE_ _ _0") for each adjustment menu and checking the values with the on-screen display. If the projector receives adjustment/setting commands other than menu display commands, it will execute the commands without displaying the on-screen display. Commands Example: • When "BRIGHT" of INPUT 1 image adjustment is set to -10. Computer RABR _ - 1 0 → ← CONTROL CONTENTS COMMAND PARAMETER RETURN Projector OK CONTROL CONTENTS COMMAND PARAMETER RETURN POWER ON P O W R _ _ _ 1 OK OR ERR BLACK SCREEN ON I M B K _ _ _ 1 OK OR ERR BUTTONS & REMOTE CONTROL KEY BUTTONS & REMOTE CONTROL KEY STANDBY P O W R _ _ _ 0 OK OR ERR BLACK SCREEN OFF I M B K _ _ _ 0 OK OR ERR POWER STATUS P O W R ? ? ? ? 0:OFF, 1:ON INPUT 1 I R G B _ _ _ 1 OK OR ERR LAMP POWER STATUS VOLUME (0 - 60) MUTE ON MUTE OFF KEYSTONE (-127 - +127) DIGITAL SHIFT (-96 - +96) T P OW _ _ _ 1 0:OFF, 1:ON, 2:COOLING 3:SHUTTING DOWN V O L A _ _ * * OK OR ERR M U T E _ _ _ 1 OK OR ERR M U T E _ _ _ 0 OK OR ERR K E Y S * * * * OK OR ERR L N D S _ * * * OK OR ERR INPUT 2 INPUT 3 INPUT 4 INPUT CHECK FREEZE ON FREEZE OFF AUTO SYNC START I R G B _ _ _ 2 OK OR ERR I V E D _ _ _ 1 OK OR ERR I V E D _ _ _ 2 OK OR ERR I C H K _ _ _ 0 OK OR ERR F R E Z _ _ _ 1 OK OR ERR F R E Z _ _ _ 0 OK OR ERR A D J S _ _ _ 1 OK OR ERR -89 Appendix