Sony MEX-1HD Operating Instructions - Page 50

Setting the loudness, — LOUD

Page 50 highlights

Level Adjusting the cut-off frequency for the subwoofer(s) To match the characteristics of the connected subwoofer(s), you can cut out the unwanted high and middle frequency signals entering the subwoofer(s). By setting the cut-off frequency (see the diagram below), the subwoofer(s) will output only low frequency signals for clearer sound. Cut-off frequency off Setting the loudness - LOUD The bass and treble will be reinforced to enjoy clear sound at low volume. SOURCE Frequency (Hz) 1 Press (SOURCE) to select a source. 2 Press the L dial. The sound list display appears. 3 Rotate the L dial to select "SUB," then press the L dial. 4 Press (F2) (LPF). 5 Rotate the L dial to select the cut-off frequency. As you rotate the L dial, the frequency changes as follows: off (default setting) y 125Hz y 78Hz 6 Press the L dial. The normal display appears. L dial 1 Press (SOURCE) to select a source. 2 Press the L dial. The sound list display appears. 3 Rotate the L dial to select "LOUD," then press the L dial. 4 Rotate the L dial to select "On," then press the L dial. The normal display appears. To cancel the loudness Select "Off" in step 4. Note If DSO is set to "On,"or EQ7 is selected, the effects of BASS and LOUD may be hard to be recognized. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156

50
Adjusting the cut-off frequency for the
subwoofer(s)
To match the characteristics of the connected
subwoofer(s), you can cut out the unwanted high
and middle frequency signals entering the
subwoofer(s). By setting the cut-off frequency
(see the diagram below), the subwoofer(s) will
output only low frequency signals for clearer
sound.
1
Press
(SOURCE)
to select a source.
2
Press the L dial.
The sound list display appears.
3
Rotate the L dial to select “SUB,” then
press the L dial.
4
Press
(F2)
(LPF).
5
Rotate the L dial to select the cut-off
frequency.
As you rotate the L dial, the frequency
changes as follows:
off
(default setting)
y
125Hz
y
78Hz
6
Press the L dial.
The normal display appears.
Setting the loudness
— LOUD
The bass and treble will be reinforced to enjoy
clear sound at low volume.
1
Press
(SOURCE)
to select a source.
2
Press the L dial.
The sound list display appears.
3
Rotate the L dial to select “LOUD,”
then press the L dial.
4
Rotate the L dial to select “On,” then
press the L dial.
The normal display appears.
To cancel the loudness
Select “Off” in step 4.
Note
If DSO is set to “On,”or EQ7 is selected, the effects of
BASS and LOUD may be hard to be recognized.
Cut-off frequency
Frequency (Hz)
Level
off
SOURCE
L dial