Sony VPL-CS7 User Manual - Page 21

Turning Off the Power

Get Sony VPL-CS7 PDF manuals and user guides View all Sony VPL-CS7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Projecting the Picture on the room temperature or the screen angle. In this case, adjust it manually. Press the D KEYSTONE key on the Remote Commander until "V Keystone" appears on the screen, and adjust the value with the v/V/v/B key. The corrected value is effective until the power turn off. • Be careful not to let the projector down on your fingers. • Do not push hard on the top of the projector with the powered tilt adjuster out. It may be occurred malfunction. 7 Turn the zoom ring to adjust the size of the picture. 8 Turn the focus ring to adjust the focus. Attention Looking into the lens when projecting may cause injury to your eyes. Turning Off the Power 1 Press the I / 1 key. "POWER OFF? Please press I / 1 key again." appears to confirm that you want to turn off the power. Note A message disappears if you press any key except the I / 1 key, or if you do not press any key for five seconds. 2 Press the I / 1 key again. The powered tilt adjuster is put away in the projector and the lens protector closes. The ON/STANDBY indicator flashes in green and the fan continues to run for about 70 seconds (VPL-CS7)/for about 90 seconds (VPL-ES2) to reduce the internal heat. Also, the ON/ STANDBY indicator flashes quickly for the first 60 seconds. During this time, you will not be able to light up again the ON/STANDBY indicator with the I / 1 key. 3 Unplug the AC power cord from the wall outlet after the fan has stopped running and the ON/STANDBY indicator has light in red. When you cannot confirm the onscreen message When you cannot confirm the on-screen message in a certain condition, you can turn off the power by holding the I / 1 key for about two seconds. Turning Off the Power 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
21
Turning Off the Power
Projecting the Picture
on the room temperature or the screen
angle. In this case, adjust it manually.
Press the D KEYSTONE key on the
Remote Commander until “V Keystone”
appears on the screen, and adjust the
value with the
v
/
V
/
v
/
B
key. The
corrected value is effective until the
power turn off.
•
Be careful not to let the projector down
on your fingers.
•
Do not push hard on the top of the
projector with the powered tilt adjuster
out. It may be occurred malfunction.
7
Turn the zoom ring to adjust the size
of the picture.
8
Turn the focus ring to adjust the focus.
Looking into the lens when projecting may
cause injury to your eyes.
Turning Off the
Power
1
Press the
I
/
1
key.
“POWER OFF?
Please press
I
/
1
key
again.” appears to confirm that you want
to turn off the power.
A message disappears if you press any key
except the
I
/
1
key, or if you do not press
any key for five seconds.
2
Press the
I
/
1
key again.
The powered tilt adjuster is put away in
the projector and the lens protector
closes.
The ON/STANDBY indicator
flashes in green and the fan continues to
run for about 70 seconds (VPL-CS7)/for
about 90 seconds (VPL-ES2) to reduce
the internal heat. Also, the ON/
STANDBY indicator flashes quickly for
the first 60 seconds. During this time,
you will not be able to light up again the
ON/STANDBY indicator with the
I
/
1
key.
3
Unplug the AC power cord from the
wall outlet after the fan has stopped
running and the ON/STANDBY
indicator has light in red.
When you cannot confirm the on-
screen message
When you cannot confirm the on-screen
message in a certain condition, you can turn
off the power by holding the
I
/
1
key for
about two seconds.
Attention
Note