Stihl FS 250 R Product Instruction Manual - Page 25

Adjusting the Throttle Cable

Get Stihl FS 250 R PDF manuals and user guides View all Stihl FS 250 R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

English / USA Adjusting the Throttle Cable 002BA136 KN 002BA147 KN 002BA163 KN 8 8 7 74 3 5 6 1 1 Loop Handle without Barrier Bar : Place the clamp (3) in the loop handle (4) and position them both against the drive tube (5). : Fit the clamp (6) and line up the holes. : Fit washers (7) on screws (8) and insert screws in holes. Screw on the square nuts (1) as far as stop. : Go to "Securing the Loop Handle". A 9 4 10 Securing the Loop Handle : Secure the loop handle (4) approx. 8 in (20 cm) (A) forward of the control handle (9). : Line up the loop handle. : Tighten down the screws firmly - lock the nuts if necessaey. : The sleeve (10) is country-specific and must be located between the loop handle and control handle. A properly adjusted throttle cable is the precondition for correct operation in the full throttle, starting throttle and idle positions. Adjust the throttle cable only after the unit is fully assembled - the control handle must be in the normal operating position. : Use a suitable tool to push the slide to the bottom of the slot (see illustration). 24 FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
24
English / USA
FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R
Loop Handle without Barrier Bar
:
Place the clamp (
3
) in the loop
handle (
4
) and position them both
against the drive tube (
5
).
:
Fit the clamp (
6
) and line up the
holes.
:
Fit washers (
7
) on screws (
8
) and
insert screws in holes. Screw on the
square nuts (
1
) as far as stop.
:
Go to “Securing the Loop Handle”.
Securing the Loop Handle
:
Secure the loop handle (
4
) approx.
8 in (20 cm) (
A
) forward of the
control handle (
9
).
:
Line up the loop handle.
:
Tighten down the screws firmly –
lock the nuts if necessaey.
:
The sleeve (
10
) is country-specific
and must be located between the
loop handle and control handle.
A properly adjusted throttle cable is
the precondition for correct
operation in the full throttle, starting
throttle and idle positions.
Adjust the throttle cable only after
the unit is fully assembled – the
control handle must be in the normal
operating position.
:
Use a suitable tool to push the slide
to the bottom of the slot (see
illustration).
4
5
002BA136 KN
1
6
1
3
8
7
8
7
10
9
4
002BA147 KN
A
Adjusting the Throttle Cable
002BA163 KN