TASCAM DA-6400 IF-DA64 Owners Manual - Page 8

Connecting to a Dante network, LAN cables used for connections

Get TASCAM DA-6400 PDF manuals and user guides View all TASCAM DA-6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

When in switched (daisy chain) mode, use to connect another Dante device in the chain. 3 Link status/activity indicator Green indicates that a link is established between the devices. Blinking indicates that signals are being transmitted between the devices. 4 Gigabit link status indicator Orange indicates that a gigabit Ethernet link has been established. Connecting to a Dante network In order to set up and use this card, you must also set up the Ethernet network that it is connected to, a computer that runs Dante Controller and other devices that support Dante. 88LAN cables used for connections Use LAN cables that are category 5e or faster. Both crossover and straight cables can be used. CAUTION • This unit is not compatible with 100Mbps Ethernet switching hubs. Always use switching hubs that support Layer 2 and Gigabit Ethernet. • Two of these cards cannot be installed in a DA-6400 and used at the same time. It two of these cards are installed, only the one in SLOT 1 can be used. NOTE • Set the computer to set the IP address automatically. • Restarting the computer might be necessary if a previous network setting is still active on the computer. 8 TASCAM IF-DA64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
8
TASCAM
IF-DA64
When in switched (daisy chain) mode, use to connect
another Dante device in the chain.
3
Link status/activity indicator
Green indicates that a link is established between the
devices.
Blinking indicates that signals are being transmitted between
the devices.
4
Gigabit link status indicator
Orange indicates that a gigabit Ethernet link has been estab-
lished.
Connecting to a Dante network
In order to set up and use this card, you must also set up the
Ethernet network that it is connected to, a computer that runs
Dante Controller and other devices that support Dante.
8
LAN cables used for connections
Use LAN cables that are category 5e or faster.
Both crossover and straight cables can be used.
CAUTION
•
This unit is not compatible with 100Mbps Ethernet
switching hubs. Always use switching hubs that support
Layer 2 and Gigabit Ethernet.
•
Two of these cards cannot be installed in a DA-6400 and
used at the same time. It two of these cards are installed,
only the one in
SLOT 1
can be used.
NOTE
•
Set the computer to set the IP address automatically.
•
Restarting the computer might be necessary if a previous
network setting is still active on the computer.