TASCAM DA-6400 IF-DA64 Owners Manual - Page 9

Switched (daisy chain) connection, Redundant connection

Get TASCAM DA-6400 PDF manuals and user guides View all TASCAM DA-6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Switched (daisy chain) connection Dante devices can be daisy-chained when there are few connected devices and when not using a switching hub. Connect them as shown below. 88Switched (daisy chain) connection example 88Redundant connection example Primary Secondary Mixer PC Mixer IF-DA64 / DA-6400 IF-DA64 / DA-6400 HUB IF-DA64 / DA-6400 HUB NOTE • When using a switched (daisy chain) connection, connect to either the PRIMARY or SECONDARY connector. • If the number of connected devices increases, raising the latency setting will be necessary. Redundant connection For recording situations where retakes are not possible, including live performances, a connection set up like the following uses two completely independent primary and secondary networks. IF-DA64 / DA-6400 NOTE Settings for switched (daisy chain) and redundant connections do not change automatically. Change the settings on the Dante Controller Network Config screen. CAUTION • The primary and secondary networks cannot be connected to each other in any way. • Do not connect the primary and secondary networks to the same switching hub. Hub Primary Secondary 9 TASCAM IF-DA64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
TASCAM
IF-DA64
9
Switched (daisy chain) connection
Dante devices can be daisy-chained when there are few
connected devices and when not using a switching hub. Connect
them as shown below.
8
Switched (daisy chain) connection example
Mixer
IF-DA64 /
DA-6400
IF-DA64 /
DA-6400
NOTE
•
When using a switched (daisy chain) connection, connect
to either the
PRIMARY
or
SECONDARY
connector.
•
If the number of connected devices increases, raising the
latency setting will be necessary.
Redundant connection
For recording situations where retakes are not possible, including
live performances, a connection set up like the following uses two
completely independent primary and secondary networks.
8
Redundant connection example
Mixer
IF-DA64 /
DA-6400
IF-DA64 /
DA-6400
HUB
PC
HUB
Primary
Secondary
NOTE
Settings for switched (daisy chain) and redundant
connections do not change automatically. Change the
settings on the Dante Controller Network Config screen.
CAUTION
•
The primary and secondary networks cannot be
connected to each other in any way.
•
Do not connect the primary and secondary networks to
the same switching hub.
Hub
Primary
Secondary