Home » TP-Link Manuals » Bridges & Routers » TP-Link TL-R4299G » Manual Viewer

TP-Link TL-R4299G User Guide - Page 20

TL-R4299G, Network, Dynamic IP, Renew, Release

UPC - 845973040260

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

TL-R4299G Dual-WAN SMB Broadband Router User Guide DHCP sever will not take effect, until they are re-configured. Besides this, the Virtual Server and DMZ Host may change accordingly at the same time, you'd better re-configure it as well. 4.3.2 WAN Choose menu "Network→WAN", you can configure the IP parameters of the WAN on the screen below. The Router provides six connection types for WAN to connect to the Internet, they are "Dynamic IP", "Static IP" , "PPPoE", "BigPondCable" , "L2TP" and "PPTP" For configuring the WAN, you should select the connection type firstly according your needs. 1. Dynamic IP If you aren't given any login parameters and IP information, please select Dynamic IP (shown in Figure 4-4), then the router will automatically get IP parameters from your ISP. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. 14

Section	Page
Chapter 1. Introduction	7
1.1 Overview of the Router	7
1.2 Features	7
1.3 Conventions	8
Chapter 2. Hardware installation	8
2.1 Panel Layout	8
2.1.1 The Front Panel	8
2.1.2 The Rear Panel	9
2.2 System Requirements	9
2.3 Installation Environment Requirements	9
2.4 Connecting the Router	10
Chapter 3. Quick Installation Guide	11
3.1 Configure PC	11
3.2 Login	14
Chapter 4. Configuring the Router	17
4.1 Status	17
4.2 Quick Setup	19
4.3 Network	19
4.3.1 LAN	19
4.3.2 WAN	20
4.3.3 Network service detection	31
4.3.4 MAC Clone	32
4.3.5 Flow Balance	32
4.3.6 Balance Policy	34
4.3.7 WAN Port Parameter	36
4.4 DHCP	37
4.4.1 DHCP Settings	37
4.4.2 DHCP Clients List	38
4.4.3 Address Reservation	39
4.5 Forwarding	40
4.5.1 Virtual Servers	40
4.5.2 Port Triggering	42
4.5.3 DMZ	44
4.5.4 UPnP	45
4.6 Security	46
4.6.1 Firewall	46
4.6.2 IP Filtering	47
4.6.3 Domain Filtering	50
4.6.4 MAC Filtering	51
4.6.5 Screen	53
4.7 Static Routing	56
4.8 Session Limit	58
4.8.1 Session Limit	58
4.8.2 Session List	59
4.9 QoS	59
4.9.1 QoS Settings	60
4.9.2 QoS Rules List	60
4.10 IP & MAC Binding	61
4.10.1 Binding Setting	61
4.10.2 ARP List	63
4.11 Dynamic DNS	64
4.11.1 Dyndns DDNS	64
4.11.2 PeanutHull DDNS	65
4.11.3 Comexe DDNS	65
4.12 Switch Setting	66
4.12.1 Port Statistics	67
4.12.2 Port Mirror	67
4.12.3 Port Rate Control	68
4.12.4 Port Parameter	68
4.12.5 Port Status	69
4.12.6 Port VLAN	70
4.13 System Tools	70
4.13.1 Time Settings	71
4.13.2 Firmware	72
4.13.3 Factory Defaults	72
4.13.4 Backup and Restore	73
4.13.5 Reboot	74
4.13.6 Password	75
4.13.7 System Log	76
4.13.8 Remote Management	76
4.13.9 Statistics	77
4.13.10 WAN Speed Detect	78
4.13.11 IP NAT Table	80
4.13.12 NAT Source Port Settings	80
Appendix A: Specifications	81
Appendix B: FAQ	82