TP-Link TL-R4299G User Guide - Page 37

TL-R4299G

Dual-WAN SMB Broadband Router User Guide

31

Enabled.

¾

Flow Control -

This displays whether the Flow Control is Enabled, "Enabled" means the

function is enabled, "Disabled" means the function is't enabled.

¾

Negotiation Mode -

The options are: Auto Negotiation, 10M Half Duplex, 10M Full

Duplex,100M Half Duplex,100M Full Duplex.

¾

Ingress Limit Mode & Ingress Limit Speed

- Select the limit mode and limit speed for the

WAN ports.

¾

Egress Limit & Egress Limit speed

- Enable Egress Limit for WAN ports and select the limit

speed for them.

)

Note:

Egress speed limit is designed for controlling the broadcasting storm. When the current flux

oversteps the setting value, the overstepped datagrams will be discarded.

4.4

DHCP

Choose menu “

DHCP

”, you can see the submenus under the main menu:

DHCP Settings

,

DHCP

Clients List

and

Address Reservation

.

Figure 4-17

Click any of them, and you will be able to configure the corresponding function. The detailed

explanations for each submenu are provided below.

4.4.1

DHCP Settings

Choose menu “

DHCP

→

DHCP Settings

”, you can configure the DHCP in the next screen (shown

in Figure 4-18).

The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which

provides the TCP/IP configuration for all the PCs that are connected to the router on the LAN.

Section	Page
Chapter 1. Introduction	7
1.1 Overview of the Router	7
1.2 Features	7
1.3 Conventions	8
Chapter 2. Hardware installation	8
2.1 Panel Layout	8
2.1.1 The Front Panel	8
2.1.2 The Rear Panel	9
2.2 System Requirements	9
2.3 Installation Environment Requirements	9
2.4 Connecting the Router	10
Chapter 3. Quick Installation Guide	11
3.1 Configure PC	11
3.2 Login	14
Chapter 4. Configuring the Router	17
4.1 Status	17
4.2 Quick Setup	19
4.3 Network	19
4.3.1 LAN	19
4.3.2 WAN	20
4.3.3 Network service detection	31
4.3.4 MAC Clone	32
4.3.5 Flow Balance	32
4.3.6 Balance Policy	34
4.3.7 WAN Port Parameter	36
4.4 DHCP	37
4.4.1 DHCP Settings	37
4.4.2 DHCP Clients List	38
4.4.3 Address Reservation	39
4.5 Forwarding	40
4.5.1 Virtual Servers	40
4.5.2 Port Triggering	42
4.5.3 DMZ	44
4.5.4 UPnP	45
4.6 Security	46
4.6.1 Firewall	46
4.6.2 IP Filtering	47
4.6.3 Domain Filtering	50
4.6.4 MAC Filtering	51
4.6.5 Screen	53
4.7 Static Routing	56
4.8 Session Limit	58
4.8.1 Session Limit	58
4.8.2 Session List	59
4.9 QoS	59
4.9.1 QoS Settings	60
4.9.2 QoS Rules List	60
4.10 IP & MAC Binding	61
4.10.1 Binding Setting	61
4.10.2 ARP List	63
4.11 Dynamic DNS	64
4.11.1 Dyndns DDNS	64
4.11.2 PeanutHull DDNS	65
4.11.3 Comexe DDNS	65
4.12 Switch Setting	66
4.12.1 Port Statistics	67
4.12.2 Port Mirror	67
4.12.3 Port Rate Control	68
4.12.4 Port Parameter	68
4.12.5 Port Status	69
4.12.6 Port VLAN	70
4.13 System Tools	70
4.13.1 Time Settings	71
4.13.2 Firmware	72
4.13.3 Factory Defaults	72
4.13.4 Backup and Restore	73
4.13.5 Reboot	74
4.13.6 Password	75
4.13.7 System Log	76
4.13.8 Remote Management	76
4.13.9 Statistics	77
4.13.10 WAN Speed Detect	78
4.13.11 IP NAT Table	80
4.13.12 NAT Source Port Settings	80
Appendix A: Specifications	81
Appendix B: FAQ	82

TP-Link TL-R4299G User Guide - Page 37

DHCP Settings

Page 37 highlights