Thermador PRD486JDGU Installation Manual - Page 29

Installing the Leg Covers, Griddle Tilt Adjustment

Get Thermador PRD486JDGU PDF manuals and user guides View all Thermador PRD486JDGU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Installing the Leg Covers 1. Remove plastic coverings of the stainless steel 'sleeves'. 2. Place the smaller 'sleeve', with cutouts facing up, inside the larger sleeve with the openings of both stacked and facing the back (Figure 26). 3. Beneath the range, wrap the mated pieces around the leg. 4. Slide the outer sleeve up while the inner piece remains on the floor. The mating part has dimples (that you cannot see) for which the holes of the larger sleeve should seize. You should feel a definitive click, letting you know that the apparatus has been mounted to the unit (Figure 27). 5. Repeat for all visible legs. After the range is properly leveled and the leg covers have been installed, replace the Door Trim and reinstall the Oven Door(s) ("Step 4: Door Removal and Reinstallation" on page 10 for door re-installation). Figure 27: Leg Covers Installed Figure 26: Leg Covers Griddle Tilt Adjustment (Not on all models) Check the griddle adjustment by pouring two tablespoons of water on the back of the griddle plate. The water should slowly roll into the grease tray. If not, adjust the (2) screws under the back of the griddle plate. Start with one half turn counter-clockwise of the screws. Further adjustment should be made by one-quarter turn until water slowly flows into the grease tray. Ensure that the burner caps are correctly seated on the burner bases of the range's cooktop. English 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
English 27
Installing the Leg Covers
1.
Remove plastic coverings of the stainless steel
‘sleeves’.
2.
Place the smaller ‘sleeve’, with cutouts facing up,
inside the larger sleeve with the openings of both
stacked and facing the back (Figure 26).
3.
Beneath the range, wrap the mated pieces around the
leg.
4.
Slide the outer sleeve up while the inner piece remains
on the floor. The mating part has dimples (that you
cannot see) for which the holes of the larger sleeve
should seize. You should feel a definitive click, letting
you know that the apparatus has been mounted to the
unit (Figure 27).
5.
Repeat for all visible legs.
After the range is properly leveled and the leg covers have
been installed, replace the Door Trim and reinstall the
Oven Door(s) (“Step 4: Door Removal and Reinstallation”
on page 10 for door re-installation).
Griddle Tilt Adjustment
(Not on all models)
Check the griddle adjustment by pouring two tablespoons
of water on the back of the griddle plate. The water should
slowly roll into the grease tray. If not, adjust the (2) screws
under the back of the griddle plate. Start with one half turn
counter-clockwise of the screws. Further adjustment
should be made by one-quarter turn until water slowly flows
into the grease tray.
Ensure that the burner caps are correctly seated on the
burner bases of the range's cooktop.
Figure 26:
Leg Covers
Figure 27:
Leg Covers Installed