Thermador T36BB110SS View Kitchen Design and Planning Guide - Page 125

PLANNING INFORMATION Built-In Coffee Machine, Professional & Masterpiece® INSTALLATION Built-In Coffee Machine, Professional & Masterpiece® Model Options The Thermador Built-in Coffee Machine is available in two options for use in a plumbed or non-plumbed installation. Both models feature a stainless steel finish and design that coordinates with both the Professional and Masterpiece® collection. An optional trim kit is available for 30" cutout installations. Installation Considerations The information in this design guide provides key features, product dimensions, cutouts and installation specifications. Before installing a Thermador Built-in Coffee Machine, be sure to verify the cabinet dimensions and water / electrical connections. Installation instructions are subject to change. Always consult with the installation manual included with the product for complete details prior to the installation. Installation Options Plumbed With a new option for built-in drainage instead of a water tank, Thermador plumbed Built-in Coffee Machines help ensure your machine is ready to operate. A water and drain connection eliminate the need to empty a drip tray, while water replenishment flows water directly into the machine from a plumbed water source, eliminating the need to fill a water container. Non-Plumbed Thermador non-plumbed Built-in Coffee Machines can be installed without an additional water line in the home -enabling installation in a bedroom, guest room, office and beyond. Important Make sure there is adequate ventilation. To do this, remove the rear panel or cut out an opening of 19 11/16" x 15 3/4" (500 x 400 mm). There must be a gap of at least 1 3/8" (35 mm) between the wall and base of the unit or the rear panel of the unit situated above. Electrical Specifications Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable local codes. Thermador Built-in Coffee Machines are equipped with a 39-inch, 3-wire supply cord with a NEMA 5-15R plug. It is designed to be connected to a 120V AC, 60Hz, single phase power supply. Model TCM24PS TCM24TS Required Circuit Breaker 120 V, 60 Hz, 15 A 120 V, 60 Hz, 15 A Optional Accessories TCMTK30RS - 30-Inch Stainless Steel Trim Kit 11005967 Stainless Steel Milk Container 11015223 1 Lb. Bean Container 12008246 Water Filter 00573828 Descaling Tablets 00573829 Cleaning Tablets Plumbed Coffee Machine Product & Cutout Dimensions Ensure proper venting, e.g. by connecting the hose to a sink or a funnel siphon 13/8" (35 mm) min. 231/2" (597 mm) depth including transformer 7" (175 mm) 22" (558 mm) 173/4+1/8" (450+2 mm) 175/8" (449 mm) 14" (356 mm) 177/8" (455 mm) 22+5/16" (560+8 mm) 3/4" (19 mm) 233/8" (594 mm) Bean and water reservoir are removed to the front. Recommended installation height 371/2-57" (95-145 cm). Make sure that the valve of the drap tray is completely clean and the strainer is installed correctly Measurements in inches (mm) Plumbed Coffee Machine Water and Electrical Connections 22" (558 mm) 3/4" (20 mm) a bc 13/8" (36 mm) 21/2" (65 mm) min. 57/8" (min. 150 mm) | THERMADOR | BUILT-IN COFFEE MACHINE | THERMADOR | BUILT-IN COFFEE MACHINE The ventilation slots and intake openings must not be covered. Also follow the installation instructions for the appliance situated above or below. The ideal installation height for the fully automatic espresso machine, measured from the floor to the lower edge of the appliance, is 37 1/2" to 57" (95 - 145 cm). If installing the appliance above a warming drawer, the height of the recess must be 23 1/4" (590 mm). If the appliance is installed directly under a décor panel, ensure that there is a ventilation slot of at least 31 square inches (200 cm2). The ideal installation height for the fully automatic coffee machine, measured from the floor to the lower edge of the appliance, is 37 7/16" (950 mm). 246 Visit Thermador.com for complete specifications or text a Thermador model number to 21432 to have specs sent to your phone 13/4" (44 mm) (a) Water outlet 93/8" (238 mm) 6" (152 mm) (b) Cold-water connection (c) Electric terminal box Measurements in inches (mm) Measurements in inches (mm) c b a The included red hose guide must be installed. The drain hose must be guided straight at the outlet point from the machine. The drain hose must be installed with a continuous gradient and a height difference of more than 6". There should be no loops, clews, double siphon or sagging in the drain hose that can interfere with water flow or cause water accumulation in the drain hose. Visit Thermador.com for complete specifications or text a Thermador model number to 21432 to have specs sent to your phone 247