Vtech DS6472-6 User Manual - Page 128

California Energy Commission battery charging testing instructions

Get Vtech DS6472-6 PDF manuals and user guides View all Vtech DS6472-6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

Appendix California Energy Commission battery charging testing instructions This telephone is set up to comply with the energy-conserving standards right out of the box. These instructions are intended for California Energy Commission (CEC) compliance testing only. When the CEC battery charging testing mode is activated, all telephone functions, except battery charging, will be disabled. To activate the CEC battery charging testing mode: 1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with charged batteries before proceeding. 2. While you press and hold /FIND HANDSET, plug the telephone base power adapter back to the power outlet. 3. After about 20 seconds, when the IN USE light starts flashing, release /FIND HANDSET and then press it again within 2 seconds. When the phone successfully enters the CEC battery charging testing mode, the IN USE light turns off and all handsets display Put handset on BASE to register. When the phone fails to enter this mode, repeat Step 1 through Step 3 above. The telephone base will be powered up as normal if you fail to press /FIND HANDSET within 2 seconds in Step 3. To deactivate the CEC battery charging testing mode: 1. Unplug the telephone base power adapter from the power outlet, then plug it back in. Then the telephone base is powered up as normal. 2. Place the handset in the telephone base to register it back. The handset displays Registering handset.... The handset shows HANDSET X Registered and you hear a beep when the registration process completes. The registration process takes about 90 seconds to complete. 123

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
123
Appendix
California Energy Commission battery charging testing instructions
This telephone is set up to comply with the energy-conserving standards right out of the box. These
instructions are intended for California Energy Commission (CEC) compliance testing only.
When the CEC battery charging testing mode is activated, all telephone functions, except battery charging,
will be disabled.
To activate the CEC battery charging testing mode:
Unplug the telephone base power adapter from the power outlet. Make sure all handsets are
plugged with charged batteries before proceeding.
While you press and hold
/FIND HANDSET
, plug the telephone base power adapter back to the
power outlet.
After about 20 seconds, when the
IN USE
light starts flashing, release
/FIND HANDSET
and then
press it again within 2 seconds.
When the phone successfully enters the CEC battery charging testing mode, the
IN USE
light turns off and
all handsets display
Put handset on BASE to register
.
When the phone fails to enter this mode, repeat Step 1 through Step 3 above.
The telephone base will be powered up as normal if you fail to press
/FIND HANDSET
within 2
seconds in Step 3.
To deactivate the CEC battery charging testing mode:
Unplug the telephone base power adapter from the power outlet, then plug it back in. Then the
telephone base is powered up as normal.
Place the handset in the telephone base to register it back. The handset displays
Registering handset...
.
The handset shows
HANDSET X Registered
and you hear a beep when the registration process
completes. The registration process takes about 90 seconds to complete.
1.
2.
3.
1.
2.