Yamaha A5000 Owner's Manual - Page 275

MIDI Data Format 2. Channel messages Channel messages are received as follows. When Program Mode = Single and Omni SW is on, The Note ON/OFF, Control Change, Pitch Bend, After Touch, and Program Change channels have no meaning. When Program Change SW is enabled and Program Mode = Single the Basic Receive Channel is used; when Program Mode = Multi the Part 1 receive channel is used. No program change occurs when off. However, when a program change is received during internal MIDI sequencer recording, the program change is not recorded even if the Program Change SW is off. Transmission is performed when the internal MIDI sequencer is playing, and when the KNOB Control function and FKey Play function are being used. When the MIDI sequencer is playing, the MIDI events that are played back are transmitted to the internal tone generator, and also simultaneously transmitted via MIDI OUT. When Knob control used, a value related to the number of rotations is transmitted for the selected Ch and Control#. When the FKey Play function is used, Note On/Off messages will be transmitted on the specified channel with the specified note number and velocity. The velocity used when transmitting a Note Off message is fixed. Note Off messages will have a velocity of 0 if the form $8n is used, and if the form $9n is used the velocity will be determined case by case. 2.1. Reception 2.1.1. Note off Note range = C-2 - G8 Velocity range = ignored 2.1.2. Note on/off Note range = C-2 - G8 Velocity range = 0 - 127 2.1.3. Polyphonic aftertouch Not received. 2.1.4. Control changes The following parameters can be controlled. Parameters which function for each program. cntrl# parameter data range 5 Program Portamento Time 0-120 Program Portamento Rate/Time 0 - 127 0 - 127 0-120 LFO S/H Speed 0 - 127 0-120 AD Input Pan 0-120 AD Input Level 0 - 127 0 - 127 0-120 AD Input L Pan 0 - 127 0-120 AD Input R Pan 0-120 AD Input L Level 0 - 127 0 - 127 0-120 AD Input R Level 0 - 127 0-120 Program Level 0-120 EF1 Level 0 - 127 0 - 127 0-120 EF1 Pan 0 - 127 0-120 EF1 Width 0-120 EF1 Parameter 1 - 16 0 - 127 0 - 127 0-120 EF2 Level 0 - 127 0-120 EF2 Pan 0-120 EF2 Width 0 - 127 0 - 127 0-120 EF2 Parameter 1 - 16 0 - 127 0-120 EF3 Level 0-120 EF3 Pan 0 - 127 0 - 127 0-120 EF3 Width 0 - 127 0-120 EF3 Parameter 1 - 16 0-120 EF4 Level 0 - 127 0 - 127 0-120 EF4 Pan 0 - 127 0-120 EF4 Width 0-120 EF4 Parameter 1 - 16 0 - 127 0 - 127 0-120 EF5 Level 0 - 127 0-120 EF5 Pan 0-120 EF5 Width 0 - 127 0 - 127 0-120 EF5 Parameter 1 - 16 0 - 127 0-120 EF6 Level 0-120 EF6 Pan 0 - 127 0 - 127 0-120 EF6 Width 0 - 127 0-120 EF6 Parameter 1 - 16 0-120 Program LFO Depth 0 - 127 0 - 127 0-120 Control 1 Range 0 - 127 0-120 Control 2 Range 0-120 Control 3 Range 0 - 127 0 - 127 0-120 Control 4 Range 0 - 127 Parameters marked by "*" depend on the Program Control settings. A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * (A5000 only) * * * * * Parameters which function for each MIDI channel of a program cntrl# 7 10 64 65 66 parameter Volume(Level) Pan Sustain Portament ON/OFF Sostenute data range 0 - 127 0 - 127 0 - 127 0 - 127 0 - 127 Parameters which function for samples or sample banks cntrl# 0-120 parameter Pitch Mod Depth data range 0 - 127 * 0-120 Amp Mod Depth 0 - 127 * 0-120 0-120 Cutoff Mod Depth Cutoff Bias 0 - 127 * 0 - 127 * 0-120 Filter Q/Width 0 - 127 * 0-120 0-120 Pan Bias Pitch Bias 0 - 127 * 0 - 127 * 0-120 Sample Level 0 - 127 * 0-120 0-120 LFO Speed LFO Delay 0 - 127 * 0 - 127 * 0-120 AEG Attack 0 - 127 * 0-120 0-120 AEG Decay AEG Sustain Level 0 - 127 * 0 - 127 * 0-120 AEG Release 0 - 127 * 0-120 0-120 PEG Attack PEG Decay 0 - 127 * 0 - 127 * 0-120 PEG Release 0 - 127 * 0-120 0-120 PEG Init Level PEG Sustain Level 0 - 127 * 0 - 127 * 0-120 FEG Attack 0 - 127 * 0-120 0-120 FEG Decay FEG Release 0 - 127 * 0 - 127 * 0-120 FEG Init Level 0 - 127 * 0-120 0-120 FEG Sustain Level FEG Level 0 - 127 * 0 - 127 * 0-120 Pitch Bend 0 - 127 * 0-120 0-120 Wave Start Address Cutoff Distance 0 - 127 * 0 - 127 * 0-120 Filter Gain 0 - 127 * 0-120 Sample Portamento Rate/Time 0 - 127 * 0-120 Sample Control 1 Range 0 - 127 * 0-120 Sample Control 2 Range 0 - 127 * 0-120 0-120 Sample Control 3 Range Sample Control 4 Range 0 - 127 * 0 - 127 * 0-120 Sample Control 5 Range 0 - 127 * 0-120 Sample Control 6 Range 0 - 127 * Parameters marked by "*" depend on the Sample Control settings. 2.1.5. Mode messages Messages which function always cntrl# 120 121 123 parameter All sound off Reset all controllers All notes off data range 0 - 127 0 - 127 0 - 127 Messages which function for samples or sample banks cntrl# 126 127 parameter mono mode poly mode data range 0 - 127 0 - 127 2.1.6. Program changes When a program change message is received, the corresponding program is selected for playback and editing. Nothing occurs if the Program Change SW is disabled (even when internal sequencer recording is off). If Program Mode = Single, program change is received via the Basic Receive Channel (any receive channel when Omni is on). When Program Mode = Multi the Part 1 receive channel is used. 2.1.7. Pitch bend The 7 bits of the MSB are used. For functions marked "* indicates Program (or Sample) control" in "Control Change" of 3.1.4, pitch bend can be used for ctrl#. 2.1.8. Channel aftertouch Received. For functions marked "* indicates Program (or Sample) control" in "Control Change" of 2.1.4, channel aftertouch can be used for ctrl#. 275 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q A5000/A4000 • Appendix