Yamaha CLP-240 Owner's Manual - Page 65

CLP-240/230: Keyboard Stand Assembly

Get Yamaha CLP-240 PDF manuals and user guides View all Yamaha CLP-240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

ENGLISH CLP-240/230: Keyboard Stand Assembly CLP-240/230: Keyboard Stand Assembly CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble the unit in the appropriate sequence. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size. Using of incorrect screws can cause damage. • Be sure to tighten all screws upon completing assembly of each unit. • To disassemble, reverse the assembly sequence. Have a Phillips-head (+) screwdriver ready. Remove all parts from the box. Confirm that all parts shown in the illustration are provided. 6 x 25 mm long screws x 4 A 6 x 16 mm short screws x 4 Styrofoam pads Take out the styrofoam pads, and place A on top of the pads. Position the styrofoam pads to protect the connector panel at the bottom of A. B Bundled pedal cord inside C 4 x 12 mm thin screws x 2 4 x 20 mm tapping screws x 4 4 x 10 mm thin screws x2 Cord holders x 2 AC power cord (The shape of plug differs depending on locale) Headphone hanger Side panel protection (cardboard) pads x 2 D E 1. Attach D and E to C. 1-1 Untie and straighten out the bundled cord. Don't discard the twist tie, you'll need it later in step 5. 1-2 Secure C using the four 6 x 25 mm long screws. 1-1 1-2 CLP-240/230 Owner's Manual 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
CLP-240/230: Keyboard Stand Assembly
CLP-240/230
Owner’s Manual
ENGLISH
65
CLP-240/230: Keyboard Stand Assembly
CAUTION
•
Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble the unit
in the appropriate sequence.
•
Assembly should be carried out by at least two persons.
•
Be sure to use the correct screw size. Using of incorrect screws can cause damage.
•
Be sure to tighten all screws upon completing assembly of each unit.
•
To disassemble, reverse the assembly sequence.
Remove all parts from the box. Confirm that all parts shown in the illustration are provided.
1.
Attach D and E to C.
1-1
Untie and straighten out the bundled cord. Don’t
discard the twist tie, you’ll need it later in step 5.
1-2
Secure C using the four 6 x 25 mm long screws.
Have a Phillips-head (+) screwdriver ready.
A
B
C
D
E
Styrofoam pads
Take out the styrofoam pads, and place A on top of the pads.
Position the styrofoam pads to protect the connector panel at
the bottom of A.
Bundled pedal cord inside
6 x 25 mm long screws x 4
6 x 16 mm short screws x 4
4 x 12 mm thin screws x 2
4 x 20 mm tapping screws x 4
4 x 10 mm thin screws x2
Cord holders x 2
AC power cord
Headphone hanger
Side panel protection
(cardboard) pads x 2
(The shape of plug differs
depending on locale)
1-2
1-1