Yamaha HTR 5890 MCXSP10 Manual - Page 31

Starting the setup, SET MENU, AUTO:MENU - thx

Get Yamaha HTR 5890 - A/V Surround Receiver PDF manuals and user guides
UPC - 027108922133
View all Yamaha HTR 5890 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

PREPARATION p p AUTO SETUP p p Starting the setup For best results, make sure the room is as quiet as possible during the auto setup procedure (YPAO). If there is too much ambient noise, the results may not be satisfactory. y If your subwoofer can adjust the output volume and the crossover frequency, set the volume to about half way (or slightly less) and set the crossover frequency to the maximum. VOLUME CROSSOVER/ HIGH CUT MIN MAX MIN MAX Subwoofer 1 Switch on this unit and video monitor. Make sure the OSD is displayed (see page 50). 2 Set AMP/SOURCE/TV to AMP, then press SET MENU to enter the SET MENU. AMP SOURCE then SET MENU MENU TV 3 Press k / n to select AUTO SETUP, then press h once to enter the main menu. ENTER SET MENU . ;AUTO SETUP ;MANUAL SETUP / : Up/Down : Enter 4 Press k / n repeatedly to select WIRING, DISTANCE, SIZE, EQUALIZING or LEVEL. 1 AUTO:MENU . WIRING;;;;;CHECK DISTANCE;;;CHECK SIZE;;;;;;;CHECK EQUALIZING;;FLAT LEVEL;;;;;;CHECK SETUP;;;;;;;AUTO START PUSH > / : Up/Down : Select 5 When WIRING, DISTANCE, SIZE or LEVEL is selected, press l / h to select: CHECK SKIP To automatically check and adjust the selected item. To skip the selected item and perform no adjustments. Note When using THX speakers, set SIZE to SKIP and make sure that "SMALL" or "SMLx2" is selected in SPEAKER SET (page 55) and that 80Hz (THX) is selected in CROSS OVER (page 57). When EQUALIZING is selected, press l / h to select: FRONT To adjust the frequency response of each speaker in accordance with the sound of your front speakers. Recommended if your front speakers are of much higher quality than your other speakers. FLAT To average the frequency response of all speakers. Recommended if all of your speakers are of similar quality. LOW To average the frequency response of all speakers, giving priority to the accuracy of bass frequencies. MID To average the frequency response of all speakers, giving priority to the accuracy of mid-range frequencies. HIGH To average the frequency response of all speakers, giving priority to the accuracy of high frequencies. SKIP To skip the selected item and perform no adjustments. 6 Press n to select SETUP, then press l / h to select: AUTO To automatically perform the entire auto setup procedure. ENTER STEP To pause for confirmation between each check in the auto setup procedure. RELOAD To restore the last auto setup setting. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
27
AUTO SETUP
PREPARATION
For best results, make sure the room is as quiet as possible
during the auto setup procedure (YPAO). If there is too
much ambient noise, the results may not be satisfactory.
y
If your subwoofer can adjust the output volume and the crossover
frequency, set the volume to about half way (or slightly less) and
set the crossover frequency to the maximum.
1
Switch on this unit and video monitor.
Make sure the OSD is displayed (see page 50).
2
Set AMP/SOURCE/TV to AMP, then press
SET MENU to enter the SET MENU.
3
Press
k
/
n
to select AUTO SETUP, then
press
h
once to enter the main menu.
4
Press
k
/
n
repeatedly to select WIRING,
DISTANCE, SIZE, EQUALIZING or LEVEL.
5
When WIRING, DISTANCE, SIZE or LEVEL is
selected, press
l
/
h
to select:
CHECK
To automatically check and adjust the selected
item.
SKIP
To skip the selected item and perform no
adjustments
.
When using THX speakers, set SIZE to SKIP and make sure
that “SMALL” or “SMLx2” is selected in SPEAKER SET
(page 55) and that 80Hz (THX) is selected in CROSS
OVER (page 57).
When EQUALIZING is selected, press
l
/
h
to select:
FRONT
To adjust the frequency response of
each speaker in accordance with the
sound of your front speakers.
Recommended if your front speakers
are of much higher quality than your
other speakers.
FLAT
To average the frequency response of
all speakers. Recommended if all of
your speakers are of similar quality.
LOW
To average the frequency response of
all speakers, giving priority to the
accuracy of bass frequencies.
MID
To average the frequency response of
all speakers, giving priority to the
accuracy of mid-range frequencies.
HIGH
To average the frequency response of
all speakers, giving priority to the
accuracy of high frequencies.
SKIP
To skip the selected item and perform
no adjustments.
6
Press
n
to select SETUP, then press
l
/
h
to
select:
AUTO
To automatically perform the entire
auto setup procedure.
STEP
To pause for confirmation between
each check in the auto setup procedure.
RELOAD
To restore the last auto setup setting.
Starting the setup
CROSSOVER/
HIGH CUT
MIN
MAX
Subwoofer
VOLUME
MIN
MAX
SET MENU
MENU
AMP
SOURCE
TV
then
±±
SET MENU
.
;
AUTO SETUP
;
MANUAL SETUP±±±
: Up/Down
p
/
p
: Enter
</>
ENTER
ENTER
Note
1
AUTO:MENU
.
±WIRING
;;;;;
CHECK
±±DISTANCE
;;;
CHECK
±±SIZE
;;;;;;;
CHECK
±±EQUALIZING
;;
FLAT
±±LEVEL
;;;;;;
CHECK
±±SETUP
;;;;;;;
AUTO±
±±START
PUSH
: Up/Down
p
/
p
: Select
</>
>