Yamaha HTR 5890 MCXSP10 Manual - Page 34

After auto setup, W-1:OUT OF PHASE, W-2:OVER 24m, W-3:LEVEL ERROR, W-4:SWFR PHASE - problems

Get Yamaha HTR 5890 - A/V Surround Receiver PDF manuals and user guides
UPC - 027108922133
View all Yamaha HTR 5890 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

AUTO SETUP After auto setup Press l / h to display the detailed information about individual warnings. Warning message W-1:OUT OF PHASE W-2:OVER 24m (80ft) W-3:LEVEL ERROR W-4:SWFR PHASE W-5:VOL ERROR Cause Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. The distance between the speaker and the listening position is over 24 m (80 ft). Remedy • Check the speaker connections for proper polarity (+ or -). • Bring the speaker closer to the listening position. The difference of volume level among speakers is excessive. (No level correction is made.) • Readjust the speaker installation so that all speakers are set in locations with similar conditions. • Check the speaker connections. • Use speakers of similar quality. • Adjust the output volume of the subwoofer. The phase polarity of the subwoofer is not correct. • Select the opposite phase on the subwoofer if the subwoofer has a phase switch. The result may not be correct because the volume was changed during the auto setup procedure. • Perform the auto setup procedure again. Do not change the volume during the auto setup procedure. • If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again. • If warning W-1, W-4 or W-5 appears, corrections are made, but they may not be optimal. • If warning W-2 or W-3 appears, no corrections are made. • If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
30
AUTO SETUP
After auto setup
Press
l
/
h
to display the detailed information about individual warnings.
•
If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again.
•
If warning W-1, W-4 or W-5 appears, corrections are made, but they may not be optimal.
•
If warning W-2 or W-3 appears, no corrections are made.
•
If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center.
Warning message
Cause
Remedy
W-1:OUT OF PHASE
Speaker polarity is not correct. This message
may appear depending on the speakers even
when the speakers are connected correctly.
•
Check the speaker connections for proper polarity
(+ or –).
W-2:OVER 24m
(80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
•
Bring the speaker closer to the listening position.
W-3:LEVEL ERROR
The difference of volume level among speakers
is excessive. (No level correction is made.)
•
Readjust the speaker installation so that all speakers
are set in locations with similar conditions.
•
Check the speaker connections.
•
Use speakers of similar quality.
•
Adjust the output volume of the subwoofer.
W-4:SWFR PHASE
The phase polarity of the subwoofer is not
correct.
•
Select the opposite phase on the subwoofer if the
subwoofer has a phase switch.
W-5:VOL ERROR
The result may not be correct because the
volume was changed during the auto setup
procedure.
•
Perform the auto setup procedure again. Do not
change the volume during the auto setup procedure.