Yamaha RX-V2600 Owner's Manual - Page 85

Volume Trim Volume trimming, Rename Rename, I/O Assignment, Input/output assignment, Example 1

Get Yamaha RX-V2600 PDF manuals and user guides
UPC - 027108924397
View all Yamaha RX-V2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

■ Volume Trim (Volume trimming) You can adjust the level of the signal input at each jack. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources. Manual Setup > Input Select > input source (DVD, etc.) > Volume Trim > Control range: -6.0 dB to +6.0 dB Audio Select Decoder Mode Volume Trim Rename 0.0dB Note You can only adjust the volume for the current input source using this setting. ■ Rename (Rename) Use this feature to change the name of the inputs in the GUI or the front panel display menu. (DVD is used as the source component in the following example.) Input Select > input source (DVD, etc.) > Rename 1 Press an input selector button to select the input you want to change the name of. 2 Press l / h to place the _ (under-bar) under the space or character you want to edit. Decoder Mode Volume Trim Rename CAPITAL DVD OK RESET SYSTEM OPTIONS 5 Press l / h to select OK and press ENTER when complete. y To change source names in the display window on the remote control, see page 109. Note You can only change the name of the current input source (except for multi channel input sources) using this setting. ■ I/O Assignment (Input/output assignment) You can assign the digital audio input/output and component video jacks to other components if this unit's initial settings do not correspond to your needs. Change the following parameters to reassign the jacks and effectively connect more components. Once the jacks are reassigned, you can select the corresponding component using the INPUT selector on the front panel or the input selector buttons on the remote control. Input Select > input source (DVD, etc.) > I/O Assignment > Example 1: To assign the COAXIAL 7 (CD) jack to the DVD input. 1) Select Input Select and then select DVD. 2) Select I/O Assignment > Coaxial Input and then select 7 CD. Example 2: To clear a jack assignment. 1) Select Input Select and then select the input source (DVD, etc.). 2) Select I/O Assignment and then select the jack assignment (Coaxial Input, Optical Input, Optical Output, Component Video, or HDMI). 3) Select NONE and then press ENTER to clear the assignment. 3 Press ENTER to select a character type (CAPITAL/SMALL/FIGURE/MARK). 4 Press k / n to select the character you want to use and l / h to move to the next one. • You can use up to 8 characters for each input. • Press n to change the character in the following order, or press k to go in the reverse order. Press ENTER to switch between character types: CAPITAL A to Z, space SMALL a to z, space FIGURE 0 to 9, space MARK etc. • Repeat steps 1 to 3 to rename each input. I/O Assignment Audio Select Decoder Mode Optical Output Component Video HDMI Notes • You cannot select a specific item more than once for the same type of jack. • When you connect a component to both the COAXIAL and OPTICAL jacks, priority is given to signals input at the COAXIAL jack. ADVANCED OPERATION 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
81
SYSTEM OPTIONS
ADVANCED
OPERATION
■
Volume Trim (Volume trimming)
You can adjust the level of the signal input at each jack.
This is useful if you want to balance the level of each input
source to avoid sudden changes in volume when switching
between input sources.
Manual Setup > Input Select > input source (DVD, etc.) >
Volume Trim >
Control range: –6.0 dB to +6.0 dB
You can only adjust the volume for the current input source using
this setting.
■
Rename (Rename)
Use this feature to change the name of the inputs in the
GUI or the front panel display menu. (DVD is used as the
source component in the following example.)
Input Select > input source (DVD, etc.) > Rename
1
Press an input selector button to select the
input you want to change the name of.
2
Press
l
/
h
to place the _ (under-bar) under
the space or character you want to edit.
3
Press ENTER to select a character type
(CAPITAL/SMALL/FIGURE/MARK).
4
Press
k
/
n
to select the character you want
to use and
l
/
h
to move to the next one.
•
You can use up to 8 characters for each input.
• Press
n
to change the character in the following
order, or press
k
to go in the reverse order. Press
ENTER to switch between character types:
CAPITAL
A to Z, space
SMALL
a to z, space
FIGURE
0 to 9, space
MARK
!, #, %, &, etc.
•
Repeat steps 1 to 3 to rename each input.
5
Press
l
/
h
to select OK and press ENTER
when complete.
y
To change source names in the display window on the remote
control, see page 109.
You can only change the name of the current input source
(except for multi channel input sources) using this setting.
■
I/O Assignment
(Input/output assignment)
You can assign the digital audio input/output and
component video jacks to other components if this unit’s
initial settings do not correspond to your needs. Change
the following parameters to reassign the jacks and
effectively connect more components.
Once the jacks are reassigned, you can select the
corresponding component using the INPUT selector on
the front panel or the input selector buttons on the remote
control.
Input Select > input source (DVD, etc.) >
I/O Assignment >
Example 1:
To assign the COAXIAL
7
(CD) jack to the DVD input.
1)
Select Input Select and then select DVD.
2)
Select I/O Assignment > Coaxial Input and then select
7
CD.
Example 2:
To clear a jack assignment.
1)
Select Input Select and then select the input source
(DVD, etc.).
2)
Select I/O Assignment and then select the jack
assignment (Coaxial Input, Optical Input, Optical
Output, Component Video, or HDMI).
3)
Select NONE and then press ENTER to clear the
assignment.
•
You cannot select a specific item more than once for the same
type of jack.
•
When you connect a component to both the COAXIAL and
OPTICAL jacks, priority is given to signals input at the
COAXIAL jack.
Note
Volume Trim
Rename
Decoder Mode
Audio Select
0.0dB
CAPITAL
OK
RESET
DVD
Decoder Mode
Volume Trim
Rename
Note
Notes
Component Video
Optical Output
HDMI
I/O Assignment
Audio Select
Decoder Mode