ZyXEL PLA491 User Guide - Page 40

press 2 seconds, within 2, minutes, ENCRYPT

Get ZyXEL PLA491 PDF manuals and user guides View all ZyXEL PLA491 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Chapter 4 The ENCRYPT Button Figure 19 ENCRYPT Connection Procedure press 2 seconds press 2 seconds within 2 minutes 5 Repeat step 4 in this section for the other powerline device you wish to connect. This must be done within 120 seconds of pressing the ENCRYPT button on the PLA-4xx. 6 Check the lights on the two powerline devices. The power ( ) and HomePlug ( ) lights should be blinking while the devices are connecting. Several times all lights blink simultaneously and the HomePlug ( ) light also shows red. Wait for about one minute while your powerline devices connect. V If the power ( ) light does not blink when you press ENCRYPT, you have probably pressed the ENCRYPT button for too long. Try again, pressing the ENCRYPT button for 1~ 2 seconds. V If the HomePlug ( ) lights on both powerline devices do not light up, the powerline devices are not connected. Repeat steps 4 and 5 in this section. If that doesn't work, see the Troubleshooting in Section 7.5 on page 74 for suggestions. 7 To add more powerline devices to your network, press the ENCRYPT button on device C (shown below) for more than 10 seconds until the power ( ) light flashes. 8 Then repeat steps 4 and 5 in this section using any powerline device (A or B) you have connected using ENCRYPT and the powerline device you want to connect (C). You must use the ENCRYPT button on both devices. 40 PLA-4xx Series User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Chapter 4 The ENCRYPT Button
PLA-4xx Series User’s Guide
40
Figure 19
ENCRYPT Connection Procedure
5
Repeat step
4
in this section for the other powerline device you wish to connect. This
must be done within 120 seconds of pressing the
ENCRYPT
button on the PLA-4xx.
6
Check the lights on the two powerline devices. The power (
) and HomePlug (
)
lights should be blinking while the devices are connecting. Several times all lights blink
simultaneously and the HomePlug (
) light also shows red. Wait for about one minute
while your powerline devices connect.
If the power (
) light does not blink when you press
ENCRYPT
, you have
probably pressed the
ENCRYPT
button for too long. Try again, pressing the
ENCRYPT
button for 1~ 2 seconds.
If the HomePlug (
) lights on both powerline devices do not light up, the
powerline devices are not connected. Repeat steps 4 and 5 in this section. If
that doesn’t work, see the Troubleshooting in Section 7.5 on page 74 for
suggestions.
7
To add more powerline devices to your network, press the
ENCRYPT
button on device
C
(shown below) for more than 10 seconds until the power (
) light flashes.
8
Then repeat steps
4
and
5
in this section using any powerline device (
A
or
B
) you have
connected using
ENCRYPT
and the powerline device you want to connect (
C
). You
must use the
ENCRYPT
button on both devices.
press 2 seconds
press 2 seconds
within 2
minutes