AIWA NSX-V2100 Operating Instructions - Page 14

SETTING

THE TIMER

1

2,4

1,2

6

The unit can be turned on at a specified time every day with the

built-in timer.

Preparation

Make sure the clock is set correctly. (See page 4.)

1

2

3

4

Press

the TIMER

button

on the

remote

control

white pressing

the SHIFT

button

once to display

0,

and press the 11 SET button within 4 seconds.

O

is displayed,

and the hour flashes.

m

If you do not press the I I SET button within 4 seconds, another

operation

may start.

Designate

the

hour

of

the

timer-on

time

by

pressing

the

1<<

DOWN

or

>1 UP button,

and

the 11 SET button.

Repeat to designate

the minute

of the timer-on

time.

After you designate the timer-on time, TIMER and one of the

source name flashes alternately on the display for 4 seconds.

Within

4 seconds,

press

one

of the

function

buttons

to select

a source.

“TIMER

and the selected

source name flash alternately

for

4 seconds.

If

this step is not completed

within 4 seconds,

repeat from

step 1.

If the TUNER button is pressed, the band cannot be selected

in this step.

Within

4 seconds,

select

the

duration

for

the

timer-activated

period with the l<<

DOWN or WI

UP button.

5

6

7

The duration for the timer-activated

period can be set between

5 and 240 minutes in 5-minute steps.

If this step is not completed

within 4 seconds,

repeat from

step 1.

Prepare

the source.

To listen to a CD,

load the disc to be played first on tray 1.

To listen to a tape,

insert the tape into deck 1 or 2.

To listen to the radio,

tune in to a station.

Press the POWER

button to turn the unit off after

adjusting

the volume

and tone.

O

remains on the display after the power is turned off (timer

standby mode).

Get

ready

for

the

TAPE

function

or the

timer

recording.

To listen to the tape, press the >

button.

To record the source, press the

button on deck 1.

When the timer-on

time is reached,

the unit turns on and

begins

play with the selected

source.

While the timer is in

operation,

the display indication

is dimmer than usual.

The timer

recording

period

and tape length

When the length of the tape to be recorded

is shorter than the

timer recording period, the

button on deck 1 is released before

the timer is

off.

When the tape length is longer than the timer recording period,

the

button is not released.

If the

is not released for a long

time, the tape in the deck may be damaged.

Press the 9/S

button to release the .

button.

To cancel

the timer

standby

mode temporarily

While pressing

the SHIFT button,

press the TIMER

button so

that 0

goes out in the display.

To restore the timer standby mode, press the TIMER button while

pressing the SHIFT button to display 0.

If using the unit after setting

the timer

After setting the timer, you can use the unit. After using the unit,

check whether the contents in steps 5 and 6 are set as you wish,

turn off the power and set step 7 if necessary.

To change

the specified

time and function

Repeat all the steps again.

To check

the specified

contents

While pressing the SHIFT button, press the TIMER button.

The

timer-on time is displayed for 4 seconds.

- Timer

playback

and timer

recording

will not begin

unless

the

power is turned off.

Connected equipment cannot be turned on and off by the built-

in timer of this unit. Use an external timer.

13

ENGLISH

AIWA NSX-V2100 Operating Instructions - Page 14

Setting, The Timer

Page 14 highlights