Bernina 730 Manual - Page 49

no.1.5-1.7

Get Bernina 730 PDF manuals and user guides View all Bernina 730 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Fitr 64 9. Set zigzag lever 18 to 3.5 and sew a few end stitches for the bar. In doing so, pull material lightly towards you to shorten the feed. Last needle hole should be to the left. Allow needle to penetrate material only with its point. 10. Set zigzag knob 18 once more to no.1.5-1.7 and sew the second edge over a somewhat shorter length than the first one. Last needle hole to the left. 11. Set zigzag knob 18 again at twice the bead width and sew the end stitches for the buttonhole bar. Again pull material somewhat back to shorten the feed. Last needle hole on the left. 12. Set zigzag knob 18 at zero position and sew a few fastening stitches, again pulling the material lightly towards you to shorten the feed. 13. Finally lay the work on the wooden support and cut the cloth between both edges (see fig. 65). File. 65 l.nat elltch on the left Lott en the left 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
11.
Set
zigzag
knob
18
again
at
twice
the
bead
width
and
sew
the
end
stitches
for
the
buttonhole
bar.
Again
pull
material
somewhat
back
to
shorten
the
feed.
Last
needle
hole
on
the
left.
12.
Set
zigzag
knob
18
at
zero
position
and
sew
a
few
fastening
stitches,
again
pulling
the
material
lightly
towards
you
to
shorten
the
feed.
13.
Finally
lay
the
work
on
the
wooden
support
and
cut
the
cloth
between
both
edges
(see
fig.
65).
File.
65
Fitr
64
9.
Set
zigzag
lever
18
to
3.5
and
sew
a
few
end
stitches
for
the
bar.
In
doing
so,
pull
material
lightly
to-
wards
you
to
shorten
the
feed.
Last
needle
hole
should
be
to
the
left.
Allow
needle
to
penetrate
ma-
terial
only
with
its
point.
10.
Set
zigzag
knob
18
once
more
to
no.1.5-1.7
and
sew
the
second
edge
over
a
somewhat
shorter
length
than
the
first
one.
Last
needle
hole
to
the
left.
l.nat
elltch
on
the
left
Lott
en
the
left
47