Home » Brother International Manuals » Sewing Machines » Brother International BAS-342G » Manual Viewer

Brother International BAS-342G Instruction Manual - English - Page 44

List of memory switch settings - service manual

Get Brother International BAS-342G PDF manuals and user guides

View all Brother International BAS-342G manuals

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

7. USING THE OPERATION PANEL (ADVANCED OPERATIONS) 7-3. List of memory switch settings No. Setting range Setting items Initial value Work clamp lift timing after sewing is completed 001 OFF Lifts at the final stitch position. ON ON Lifts after moving to the home position. Integrated-type work clamp drop operation 002 0 Work clamp dropping in one step 1 Work clamp dropping in two steps (*1) 0 2 Do not use this setting. Sewing start speed The sewing speed for the first 1 − 5 stitches is set by memory switch numbers 151 100 OFF − 155. (Refer to the service manual for details of memory switch Nos. 151 − 155.) OFF ON 1st stitch at 400 rpm, 2nd stitch at 400 rpm, 3rd stitch at 600 rpm, 4th stitch at 900 rpm, 5th stitch at 2,000 rpm Single-stitch test feed OFF Test feed starts when the start switch is depressed, and it continues automatically until the final stitch. 200 Test feeding OFF ON • Is carried out one stitch at a time each time the work clamp switch is depressed • Is carried out continuously while the start switch is depressed • Is carried out one stitch at a time when the pulley is turned by hand Production counter display 300 OFF Lower thread counter display OFF ON Production counter display User programs 400 OFF Disabled OFF ON User program mode is enabled. Cycle programs 401 OFF Disabled OFF ON When sewing user programs, the set programs are sewn in numeric order. Maximum reduction ratio (mm display) (*2) 402 OFF Displayed as %. OFF ON Displayed as mm. Split mode selection 403 0 Continuous split (split menu is disabled before split detection) 1 Continuous split (split menu is always enabled) 0 2 Independent split (*1) The position of the work clamp stopper must be set. (Refer to "5-8. Setting 2-step operation for the work clamp".) (*2) The mm display may differ slightly from the actual sewing size. 35 BAS-342G

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
CONTENTS	8
1. NAMES OF MAJOR PARTS	10
2. SPECIFICATIONS	11
3. TABLE PROCESSING DIAGRAM	12
4. INSTALLATION	13
4-1. Removing the machine head fixing bolts [1]	13
4-2. Installing the control box [2]	14
4-3. Installing the oil pan and support lever base	15
4-4. Installing the machine head	15
4-5. Tilting back and returning the machine head	16
4-6. Installing the gas spring	17
4-7. Installing the operation panel [3]	18
4-8. Installing the solenoid valve assembly	19
4-9. Connecting the air tubes [4]	19
4-10. Installing the air hose [5]	19
4-11. Adjusting the air pressure [6]	20
4-12. Adjusting the speed controller [7]	20
4-13. Connecting the cords [8]	21
4-14. Connecting the ground wire [9]	23
4-15. Securing the cords and air tubes [10]	24
4-16. Installing the eye guard [11]	25
4-17. Installing the cotton stand [12]	25
4-18. Lubrication [13]	26
4-19. Connecting the power cord [14]	27
4-20. Checking the safety switch [15]	27
5. PREPARATION BEFORE SEWING	28
5-1. Installing the needle	28
5-2. Operating the 2-pedal foot switch	28
5-3. Threading the upper thread	29
5-4. Winding the lower thread	31
5-5. Installing the bobbin case	32
5-6. Thread tension	33
5-6-1. Lower thread tension	33
5-6-2. Upper thread tension	33
5-7. Home position detection	34
5-8. Setting 2-step operation for the work clamp	35
6. USING THE OPERATION PANEL (BASIC OPERATIONS)	36
6-1. Name and function of each operation panel item	36
6-2. Loading sewing data	38
6-3. Setting the program number	38
6-4. Setting the X-scale and Y-scale	39
6-5. Setting the sewing speed	39
6-6. Checking the sewing pattern	40
6-7. Setting the height of the intermittent presser foot	41
7. USING THE OPERATION PANEL (ADVANCED OPERATIONS)	42
7-1. List of advanced functions	42
7-2. Setting memory switches	43
7-3. List of memory switch settings	44
7-4. Using the lower thread counter	45
7-5. Using the production counter	46
7-6. Setting the split number	47
7-7. Using user programs	48
7-8. Using cycle programs	51
7-9. Direct selection (combination table)	53
7-10. X and Y parallel movement of sewing pattern	54
7-11. Clearing memory data (reinitialization)	55
8. USING CF CARDS	56
8-1. Notes on handling CF cards (sold separately)	56
8-2. Structure of a CF card folder	56
8-3. Data read/write mode	57
8-3-1. Reading all sewing data from the CF card at once	58
8-3-2. Writing all sewing data to the CF card at once	59
9. SEWING	60
9-1. Sewing	60
9-2. Using the STOP switch	61
9-3. Using the thread wiper switch	61
10. CLEANING	62
10-1. Cleaning the rotary hook	62
10-2. Draining the oil	62
10-3. Checking the regulator	63
10-4. Cleaning the control box air inlet ports	63
10-5. Cleaning the eye guard	63
10-6. Checking the needle	63
10-7. Lubrication	63
11. STANDARD ADJUSTMENTS	64
11-1. Adjusting the thread take-up spring	64
11-2. Adjusting arm thread guide R	65
11-3. Adjusting the needle bar height	65
11-4. Adjusting the needle bar lift amount	65
11-5. Adjusting the driver needle guard	66
11-6. Adjusting the needle clearance	66
11-7. Adjusting the shuttle race thread guide	66
11-8. Adjusting the rotary hook lubrication amount	67
11-9. Adjusting the position of the movable knife	68
11-10. Replacing the movable and fixed knives	70
11-10-1. Installing the feed plate	71
11-11. Adjusting the thread wiper	71
11-12. Presser foot installation position	72
11-13. Changing the intermittent stroke	72
11-14. Adjusting the work clamp lift amount	74
11-15. Adjusting the air pressure	74
12. TABLE OF ERROR CODES	75
13. TROUBLESHOOTING	79
14. 7-SEGMENT DISPLAY	82