Brother International BAS-342G Instruction Manual - English - Page 54

X and Y parallel movement of sewing pattern, End parallel movement mode

Get Brother International BAS-342G PDF manuals and user guides View all Brother International BAS-342G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

7. USING THE OPERATION PANEL (ADVANCED OPERATIONS) 7-10. X and Y parallel movement of sewing pattern You can move the feed mechanism to the desired position to move an already-programmed sewing pattern in a parallel direction up, down or to the left or right. 1 1. Press the or key to select the program number. 2. Depress the work clamp switch (1) to lower the work clamp, and then depress the start switch (2). • The work clamp will move to the sewing start position. 2 Depress the work clamp switch (1) to lower the work clamp. 3 While pressing the TEST key, press the 4974Q 4014M key. • The parallel movement amount will appear in the menu display in units of mm. TEST indicator illuminates, X-SCALE indicator flashes 4975Q 4559Q 4 X-scale parallel movement mode Press the SELECT key to switch between the X-SCALE Y-scale indicator and Y-SCALE indicator flashing. Select either parallel movement mode direction. 5 End parallel movement mode 4560Q 4561Q The work clamp will move by 0.05 mm each time the or key is pressed. (When the distance reaches 10 mm, the amount of movement will change to 0.1 mm.) • When using X-scale parallel movement mode, the needle moves the corresponding distance to the right when the key is pressed, and to the left when the key is pressed. • When using Y-scale parallel movement mode, the needle moves the corresponding distance backward when the key is pressed, and forward when the key is pressed. Press the TEST key. TEST indicator switches off NOTE: • The feed mechanism will not move to a position that would move the sewing pattern outside the sewing area. • If you change the program number, X-scale or Y-scale settings, the amount of movement recorded will be reset. • In addition, the amount of movement will be reset if the power switch is turned off and then back on again. However, memory switch No. 465 is set to "ON", the amount of movement will be recorded and will not be reset. (Refer to the service manual for details on memory switch No. 465.) 45 BAS-342G

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
7. USING THE OPERATION PANEL (ADVANCED OPERATIONS)
45
BAS-342G
7-10. X and Y parallel movement of sewing pattern
You can move the feed mechanism to the desired position to move an already-programmed sewing pattern in a parallel
direction up, down or to the left or right.
1
1. Press the
or
key to select the program number.
2. Depress the work clamp switch (1) to lower the work
clamp, and then depress the start switch (2).
•
The work clamp will move to the sewing start
position.
2
Depress the work clamp switch (1) to lower the work clamp.
3
TEST indicator illuminates, X-SCALE indicator flashes
While pressing the TEST key, press the
key.
•
The parallel movement amount will appear in the menu
display in units of mm.
4
X-scale
Y-scale
parallel movement mode
parallel movement mode
Press the SELECT key to switch between the X-SCALE
indicator and Y-SCALE indicator flashing. Select either
direction.
The work clamp will move by 0.05 mm each time the
or
key is pressed. (When the distance reaches 10
mm, the amount of movement will change to 0.1 mm.)
•
When using X-scale parallel movement mode, the
needle moves the corresponding distance to the right
when the
key is pressed, and to the left when the
key is pressed.
•
When using Y-scale parallel movement mode, the
needle moves the corresponding distance backward
when the
key is pressed, and forward when the
key is pressed.
5
End parallel movement mode
TEST indicator switches off
Press the TEST key.
NOTE:
•
The feed mechanism will not move to a position that would move the sewing pattern outside the sewing area.
•
If you change the program number, X-scale or Y-scale settings, the amount of movement recorded will be reset.
•
In addition, the amount of movement will be reset if the power switch is turned off and then back on again. However,
memory switch No. 465 is set to "ON", the amount of movement will be recorded and will not be reset. (Refer to the
service manual for details on memory switch No. 465.)
4974Q 4014M
4975Q
4559Q
4561Q
4560Q