Brother International BAS-415 Instruction Manual - English - Page 30

turning, power, machine

Get Brother International BAS-415 PDF manuals and user guides View all Brother International BAS-415 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

ra; El When turning on the power of the machine [NOTE] When the needle bar and the pulley are not in the stop position or if even one of the needle thread take- ups is not in line, lift the needle thread take-up 0 0 with a finger. The needle thread take-ups form a straight line at the top of the guide plate. 0 1. If the following are displayed (1) This message shows that the needle bar case is not aligned with the needle hole of the needle plate. The machine cannot operate under this condition. needle bar case side 0 0 1. First of all, check that the needle bar stop position is correct. When the red mark @ of the clutch knurl 0 is on the side of the needle bar case, it is in the automatic jump condition. This is the normal position. 2. Turn the shaft © slowly. If it is unusually heavy or does not turn, the needle thread take-up 0 or the needle bar is not in the proper position. Check again and adjust it [NOTE] Do not turn the shaft forcefully. 3. When the needle bar case comes to the proper position, in the middle of the undetected area where the needle bar 0 case does not move although the shaft is turned, the buzzer sounds 'beep' and the messages, "CAUTION MOVING!" and "Press START key" are alternately displayed. START 4. Press the key. - 27 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
ra;
El
When
turning
on
the
power
of
the
machine
0
0
1.
If
the
following
are
displayed
(1)
needle
bar
case
side
0
0
0
START
[NOTE]
When
the
needle
bar
and
the
pulley
are
not
in
the
stop
position
or
if
even
one
of
the
needle
thread
take-
ups
is
not
in
line,
lift
the
needle
thread
take-up
0
with
a
finger.
The
needle
thread
take-ups
form
a
straight
l
ine
at
the
top
of
the
guide
plate.
This
message
shows
that
the
needle
bar
case
is
not
aligned
with
the
needle
hole
of
the
needle
plate.
The
machine
cannot
operate
under
this
condition.
1.
First
of
all,
check
that
the
needle
bar
stop
position
is
correct.
When
the
red
mark
@
of
the
clutch
knurl
0
is
on
the
side
of
the
needle
bar
case,
it
is
in
the
automatic
jump
condition.
This
is
the
normal
position.
2.
Turn
the
shaft
©
slowly.
If
it
is
unusually
heavy
or
does
not
turn,
the
needle
thread
take-up
0
or
the
needle
bar
is
not
in
the
proper
position.
Check
again
and
adjust
it
[NOTE]
Do
not
turn
the
shaft
forcefully.
3.
When
the
needle
bar
case
comes
to
the
proper
position,
in
the
middle
of
the
undetected
area
where
the
needle
bar
case
does
not
move
although
the
shaft
is
turned,
the
buzzer
sounds
'beep'
and
the
messages,
"CAUTION
MOVING!"
and
"Press
START
key"
are
alternately
displayed.
4.
Press
the
<START>
key.
-
27
-