Brother International BAS-415 Instruction Manual - English - Page 79

Message, communication, Cause, Solution, replacing, needle

Get Brother International BAS-415 PDF manuals and user guides View all Brother International BAS-415 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

1 Message in communication mode Line ERR. Cause 1. Data error occurs during communicating with editing system. 2. Editing system exits from communication mode while machine is communicating with editing system. 3. Power of editing system is turned off during communicating. Solution Re-communicate. Set editing system to communication mode, then communicate again. Turn on power of editing system again, enter communication mode. Line Busy Editing system is defective, or breakdown. Turn on power of editing system again, enter communication mode_ Contact your dealer. Tape read Error 1. Poor punch of paper tape. Remake paper tape. 2. Paper tape runs short. 3. Dirty head of paper tape Clean head. reader. 4. Power of paper tape reader is Turn on the power. not turned on. 5. Paper tape type is wrongly Select proper type to read paper selected. tape. 6. improper communication baud Adjust baud rate. rate. Message in replacing needle bar Cause N_ Case POS. Error 1. Needle bar is not set properly. 2. Damaged circuit board_ Solution Position needle bar case properly. (Refer to page 27.) Contact your dealer. N _ Case Lock 1. Needle bar case is too tight mechanically, or locked and cannot move. 2. Electrical failure Remove load. Contact your dealer. - 76 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
1
Message
in
communication
mode
Cause
Solution
Line
ERR.
1.
Data
error
occurs
during
communicating
with
editing
system.
Re
-communicate.
2.
Editing
system
exits
from
Set
editing
system
to
communication
mode
while
communication
mode,
then
machine
is
communicating
with
editing
system.
communicate
again.
3.
Power
of
editing
system
is
Turn
on
power
of
editing
system
turned
off
during
communicating.
again,
enter
communication
mode.
Line
Busy
Editing
system
is
defective,
or
Turn
on
power
of
editing
system
breakdown.
again,
enter
communication
mode_
Contact
your
dealer.
Tape
read
Error
1.
Poor
punch
of
paper
tape.
Remake
paper
tape.
2.
Paper
tape
runs
short.
3.
Dirty
head
of
paper
tape
reader.
Clean
head.
4.
Power
of
paper
tape
reader
is
not
turned
on.
Turn
on
the
power.
5.
Paper
tape
type
is
wrongly
Select
proper
type
to
read
paper
selected.
tape.
6.
improper
communication
baud
rate.
Adjust
baud
rate.
Message
in
replacing
needle
bar
Cause
Solution
N
Case
POS.
Error
1.
Needle
bar
is
not
set
properly.
Position
needle
bar
case
properly.
_
2.
Damaged
circuit
board_
(Refer
to
page
27.)
Contact
your
dealer.
N
_
Case
Lock
1.
Needle
bar
case
is
too
tight
mechanically,
or
locked
and
cannot
move.
Remove
load.
2.
Electrical
failure
Contact
your
dealer.
-
76
-